Vitek VT-2350, Manual Instruction

Page: 4 / 28

4
ENGLISH
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours at
room temperature before switching on.
There may be water spots in the air humidifier, this
is normal, as the unit has undergone factory qual-
ity control.
–
Unpack the unit, remove any stickers and pack-
age materials that can prevent unit operation.
Check the unit for damages. In case of dam-
ages do not switch the unit on.
–
Remove the water tank (2) from the unit body
(6) and remove the float (8) fixing transporting
gasket, if any.
–
Install the water tank (2) back to its place.
Note: When installing the water tank (2) on the
unit body (6), it is necessary to match the air duct
(4) with the lower steam inlet of the water tank (2).
–
Before plugging the unit in make sure that your
home mains voltage corresponds to the unit
operating voltage.
–
The unit is intended for operation with AC sys-
tem and 50 Hz frequency. The unit does not
need any additional settings for operating with
the required nominal frequency.
Notes:
–
Use the air humidifier at the room temperature
from +10° С to +40°С, and relative humidity less
than 80%.
–
Water temperature should not 40°С.
AIR HUMIDIFIER OPERATION
•
Remove the lid (1) from the water tank (2).
•
Fill the tank (2) with the necessary amount of
water not exceeding the maximal level mark
(3) «МАКС».
Note: - it is recommended to use water that was
additionally cleaned with domestic filter.
•
Install the lid (1) back to its place.
•
Wait till the process chamber (7) is filled with
water.
•
Plug the power cord into a mains socket, you
will hear a sound signal and all the control panel
light indicators (5) will light up for a short time.
•
Turn the lid (1) relative to the water tank (2)
to select the optimal direction of the «mist»
release.
Notes:
–
the operation mode selection and setting but-
tons are sensory, you just need to touch the
button to switch the necessary operation mode
on, every touch of the active button is accom-
panied by a sound signal.
Warning: – do not remove the water tank (2) from
the unit body (6) when the humidifier is on, in order
to avoid splashing the unit body and the surround-
ing surface.
OPERATING BUTTONS AND INDICATION
«Mist» release on/off/intensity control
button (15) «
»
–
Consequently press the button (15) to switch
the unit on/off and to select the desired mist
release intensity level.
–
Press the button (15) to switch the unit on, the
high «mist» intensity level indicator (12) «
»
will light up on the control panel (5). Press
the button (15) again to switch the low “mist”
release intensity, the low «mist» intensity level
indicator (12) «
» will light up. Press the but-
ton (15) again to switch the unit off, all indica-
tors will go out and the «mist» release will stop.
Timer on/off button (16) « »
–
Consequently press the button (16) to set
the desired operation time of the humidifier:
2 hours, 4 hours, or 8 hours, the corresponding
operating time indicator (13) will light up on the
control panel (5). To switch the timer off press
the button (16) until all the indicators go out.
Night illumination on button (17) « »
–
Press the button (17) to switch on the night illu-
mination of the water tank (2), the illumination
color will begin to change smoothly over time.
–
During the change of colors you can select and
fix the desired color by pressing the button (17)
once again. Smooth color change will stop.
–
Press the button (17) again to switch the night
illumination off.
Sleep mode on/off button (18) « »
–
Press the button (18) to switch the sleep mode
on, the sleep mode indicator (14) on the control
panel (5) will light up, while the illumination and
other indicators will go out.
When you switch the sleep mode on,
all previous settings are saved
–
Press any button to switch the sleep mode off.