4
ENGLISH
or if they are not instructed by this person on
the usage of the unit.
•
Do not leave the operating unit unattended.
•
Unplug the unit if it is not being used and
before cleaning.
•
Do not use inflammable, highly explosive,
toxic and cleaning solvents to remove dirt.
•
When unplugging the unit, pull the plug but
not the cord.
•
Do not touch the power plug with wet hands.
•
Provide that the power cord does not contact
with hot surfaces and sharp furniture edges.
•
Do not wind the power cord around the unit body.
•
Check the cord insulation integrity periodi-
cally.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package only.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature.
ATTENTION!
The convention fan-heater is intended
only for additional heating of rooms. It is not meant
for operation as main heating unit.
•
Unpack the unit.
•
Make sure that the operation mode switch (5)
is set to the position “
0
” (the unit is switched
off).
SETTING
Option 1 – Stand mode
•
Turn the unit over. Combine openings on the
support plates (1) with wheels with relevant
openings in the lower part of the convection
fan-heater body (pic.1).
•
Fix the support plates (1) with wheels using
screws for fastening the support plates (pic. 2).
•
Turn the unit over and set it on the wheels.
Option 2 – Wall mounting
Attention!
Before drilling a hole in the wall,
make sure that there is no electrical wiring at
this place.
•
When mounting the unit on the wall, ensure
that the mains socket is below the level of
the unit and easy to access. Keep the follow-
ing gaps: between floor and unit – not less
than 15 cm, between front / upper panels
and objects – not less than 45 cm, between
side panels and objects – not less than 25
cm (pic. 7).
•
Support plates (1) with wheels are not used for
wall mounting of the convection fan-heater.
•
First mark holes on the wall (pic. 3).
•
Drill the holes in the wall to the required depth.
•
Insert the dowels into the drilled holes (pic. 4)
and fix screws for mounting the convection
fan-heater (pic.5).
•
Hang the convection fan-heater (pic.6) using
wall brackets (6) on the back side of the unit.
Using the convection fan-heater
•
Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage, and the switch (5) is in
the position “
0
” (the unit is switched off).
•
Insert the power plug into the mains socket.
•
Select the required convection fan-heater
operation mode using the switch (5):
–
I
– minimum heating power,
–
II
– maximum heating power.
Note:
–
Model VT- 2171 has the operation mode
switch (5) with only two positions -“ I/O”.
Power capacity for models of сonvection
fan-heaters:
VT-2171 –
I
– 1000 W
VT-2172 –
I
– 750 W–
II
– 1500 W
VT-2174 –
I
– 900 W –
II
– 2000 W
•
The indicator (3) will light up.
•
You may set the required room air heating level
from minimum to maximum value (
MIN
/
MAX
)
by turning the temperature control knob (4).
•
When the room temperature reaches the
required value, slowly turn the tempera-
ture control knob (4) counterclockwise until
the indicator (3) goes out. The preset tem-
perature will be maintained automatically.
If the room temperature is lower than the
temperature set by the temperature con-
trol knob (4), the unit will be switched to the
heating mode. When the preset tempera-
ture is reached, the unit will be switched to
the standby mode, once the air in the room
cools down, the unit will be switched to the
heating mode again.
IM VT-2171.indd 4
23.06.2016 14:23:12
