Visionary D4200 User Manual Download Page 24

Page: 24 / 60

Advanced Configuration

IDEO

ORMAT

ETTINGS

ECODER

NLY

)

By default, the

VIDEO.FORMAT

field on the D4200 decoder is set to

Source

. This means that the same source resolution being

encoded by the currently “tuned” D4200 is passed through to the output. This is for cases where you are certain that the display

connected to the D4200 can handle any of the source resolutions that it may be tuned to. If the connected display cannot show an

encoded resolution, set this field to a value that the display can decode. For example, if you are tuning a 4K encoded stream and are

using an HD display, set this value to 1080P60. The decoder will scale the tuned stream to 1080P60 and allow the display to show the

stream.

UDIO

ETTINGS

UDIO

OURCE

The E4200/D4200 series is capable of using HDMI or Analog audio sources.

•

The E4200 encoder uses the STREAM.AUDIO to select the source of audio sent over the AV over IP stream.

•

The D4200 decoder uses the STREAM.AUDIO to select what audio is sent out the HDMI output.

STREAM.AUDIO=HDMI

E4200 – STREAM.AUDIO = HDMI

1. Encoder receives HDMI or USB-C input with embedded audio.

3. Encoder takes embedded HDMI or USB-C audio (same as above) and encodes it into the AV over IP stream that includes video.

D4200 – STREAM.AUDIO = HDMI

1. Decoder receives AV over IP stream with both audio and video and decodes it to the HDMI and USB-C output.

STREAM.AUDIO=ANALOG (Encoders only)

E4200 – STREAM.AUDIO=Analog

Uses the Analog audio (balanced or unbalanced consumer line level via Euroblock connector) and sends it out the AV stream.

***D4200 is always passing analog audio via the Euroblock connector. D4200 allows volume level (AUDIO.VOLUME) setting of

analog audio output. AUDIO.DAC_MUTE will mute or unmute the audio being transmitted out the analog output. This output is

always the first two channels of audio in the AV over IP stream.

AUDIO.DAC_MUX=STREAM (Decoder only)

Decoder receives AV over IP stream with both audio and video and decodes just the audio to the decoder analog output.

UDIO

ONNECTIONS

Pin 1: + (Left)
Pin 2: -
Pin 3: Shield
Pin 4: + (Right)
Pin 5: -
Pin 6: Shield

Summary of Contents for D4200





























































Search results

Summary of Contents for D4200

Reviews:

Related manuals for D4200

Brands by name

Popular brands

Visionary D4200, User Manual

Search results

Summary of Contents for D4200

Reviews:

Related manuals for D4200

Brands by name

Popular brands