Viessmann Vitodens 100-W WB1B Series Installation Instructions Manual Download Page 88

Page: 88 / 92

5608 741 - 04

Vitodens Rigid and Flex Venting Systems Installation

Single Pipe Venting (Room Air Dependent)

Vent Length Requirements

Maximum vent pipe length - vertical

Legend

Combustion air intake (left, right or through co-axial

opening), remove and discard air intake cover for

(WB1B 26, 35, WB2B 19, 26, 35, B2HA 19, 28, 35,

B2HB 19, 26, 35, B2TA 19, 35 and B2TB 19, 35)

Combustion air opening

a Equivalent vent length (exhaust)

Pipe support

Maximum allowable equivalent length - vertical

Adaptors

Increaser / transition adaptors

This boiler adaptor is shown installed

with an increaser adaptor (if required

for 80 mm system) for models WB1B

26, 35, WB2B 19, 26 25, B2HA 19,

28, 35, B2HB 19, 26, 35, B2TA 19,

35 and B2TB 19, 35.

Legend

a 5

in. (140 mm)

This boiler adaptor is shown installed

with a required transition adaptor for

models WB2B 80, 105, B2HA 80,

88, 100, 112, 150. Required only

with M&G / Duravent system.

Legend

b 7

in. (191 mm)

This boiler adaptor is shown (pre-

installed) for models WB2B 45, 60,

B2HA 45, 60, B2HB 45, 57.

The connecting rigid pipe (PPs) fits

directly into the boiler adaptor.

Legend

c 2

in. (64 mm)

Note:

For combination of different vent/air intake pipe

diameters, such as Ø 3 in. (80 mm) PP(s) flexible

vent with Ø 2 in. (50 mm) CVPC, PVC, ABS air

intake pipe, the total equivalent length must be

used for the smaller pipe diameter.

Boiler Model

System Ø

See note below

Max. combined equivalent vent length

(a+b)

WB1B 26, 35

2 in. (50 mm)

3 in. (80 mm)

4 in. (100 mm)

65 ft. (20 m)

123 ft. (37 m)

150 ft. (46 m)

WB2B 19, 26, 35, B2HA 19, 28, 35, B2HB 19, 26, 35

B2TA 19, 35, B2TB 19, 35

2 in. (50 mm)

3 in. (80 mm)

4 in. (100 mm)

84 ft. (26 m)

111 ft. (34 m)

135 ft. (41 m)

WB2B 45, 60, B2HA 45, 60, B2HB 45, 57

3 in. (80 mm)

4 in. (100 mm)

74 ft. (23 m)

111 ft. (34 m)

WB2B 80, 105, B2HA 80, 88, 100, 112

4 in. (100 mm) or

4.3 in. (110 mm)

98 ft. (30 m)

B2HA 150

4 in. (100 mm)*

5 in. (125 mm)**

98 ft. (30 m)

* There is an input reduction of 9% for model B2HA 150 when a 4 in. diameter vent pipe is used.

** 4 in. to 5 in. increaser field supplied.

Summary of Contents for Vitodens 100-W WB1B Series





























































































Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews:

Viessmann Vitodens 100-W WB1B Series, Installation Instructions Manual, Page: 88 / 92

Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews: