Viessmann Vitodens 100-W WB1B Series Installation Instructions Manual Download Page 34

Page: 34 / 92

5608 741 - 04

Vitodens Rigid and Flex Venting Systems Installation

Vent Requirements - Stainless Steel

(continued)

Direct Venting (Two-pipe System)

Additional requirements for stainless steel vent pipe

material

(continued)

Viessmann single pipe PP(s) increaser and 2 in. air intake

CPVC adaptor (if using ABS/CPVC/PVC material) must be

ordered, (see table below for part number).
Minimum pipe diameter available for exhaust stainless

steel pipe is 3 in.
The air inlet (intake) cover must stay in place.

Increaser (min. stainless steel pipe diameter is 3 in. (76 mm)
Supplier

Boiler Model

PP(s) increaser

CVPC Starter Adaptor for air intake

Quantity

Viessmann

WB1B 26, 35

WB2B 19, 26, 35

B2TA 19, 35

B2TB 19, 35

B2HA 19, 28, 35

B2HB 19, 26, 35

(60 to 80 mm) (see

illustration above

2 in.

WARNING

(For this type of installation only:)

Boiler comes with pre-installed combustion air cover

mounted on the concentric vent pipe adaptor. Do not

remove combustion air intake cover. Removing this cover

may cause unintended room air dependent operation

(non-direct vent). Room air dependent operation requires

provision of combustion and ventilation air (as per

section “Single Pipe Venting”, page 53).

Air inlet (intake)

cover must stay

in place.

DO NOT remove!

Vent pipe starter adaptors for WB1B 26, 35,

WB2B 19, 26, 35, B2TA 19, 35 and B2HA 19, 28, 35

Air

Flue

Optional left

connection

for air intake

Legend

Stainless steel slip joint vent starter adaptor

2 in. CVPC starter adaptor

a 3 in. (76 mm)

b 2 in. (51 mm)

c 6.25 in. (159 mm)

d 10.34 in. (263 mm)

e 3 in. (76 mm)

Summary of Contents for Vitodens 100-W WB1B Series





























































































Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews:

Viessmann Vitodens 100-W WB1B Series, Installation Instructions Manual, Page: 34 / 92

Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews: