Viessmann Vitodens 100-W WB1B Series Installation Instructions Manual Download Page 66

Page: 66 / 92

5608 741 - 04

Vitodens Rigid and Flex Venting Systems Installation

Single Pipe Venting (Room Air Dependent)

Vent Length Requirements

Maximum vent pipe length - horizontal

All PP(s) vent material and air intake (if PP(s) used) must

be ULC S636 or UL 1738 listed, manufactured by M&G /

DuraVent or Centrotherm InnoFlue.

Size the exhaust vent pipe as specified in the table below.

This table lists the maximum allowable vent length in feet

and meters of the exhaust piping. Vent diameter must not

be reduced at any point in the installation.

First elbow not included in equivalent vent calculation.

Always include vent termination length in calculations.

IMPORTANT

Maximum allowable equivalent length - horizontal

Boiler Model

System Ø

Max. equivalent vent length ”a”

WB1B 26, 35

2 in. (51 mm)*1

3 in. (76 mm)*2

4 in. (102 mm)*2

86 ft. (31 m)

164 ft. (50 m)

200 ft. (61 m)

WB2B 19, 26, 35, B2HA 19, 28, 35, B2TA 19, 35,

B2HB 19, 26, 35, B2TB 19, 35

2 in. (51 mm)*1

3 in. (76 mm)*2

4 in. (102 mm)*2

115 ft. (35 m)

148 ft. (45 m)

180 ft. (55 m)

WB2B 45, 60, B2HA 45, 60, B2HB 45, 57

3 in. (76 mm)

4 in. (102 mm)*2

98 ft. (30 m)

148 ft. (45 m)

WB2B 80, 105, B2HA 80, 88, 100, 112

4 in. (102 mm)

131 ft. (40 m)

B2HA 150

4 in. (100 mm)*4

5 in. (125 mm)*5

131 ft. (40 m)

2 in. diameter system only available with CPVC / PP(s) system

4 in. (3 in. to 4 in. increaser field supplied).

See illustration below.

Due to higher exhaust vent pipe resistance, there is an automatic input reduction of 9% for model B2HA 150

when a 4 inch diameter vent pipe is used.

4 in. to 5 in. increaser field supplied.

Minimum vent length is 3.3 ft. (1 m).

For PP(s) systems, all exhaust vent and air intake piping

and elbows exposed outside, must be UV resistant

polypropylene (supplied by the vent manufacturer).

IMPORTANT

Vitodens 100-W WB1B 26, 35,

Vitodens 222-F B2TA 19, 35,

Vitodens 222-F B2TB 19, 35,

Vitodens 200-W WB2B 19, 26, 35

Vitodens 200-W B2HA 19, 28, 35,

Vitodens 200-W B2HB 19, 26, 35,

Flue

Side wall

Flue starter adaptor - Stainless Steel & CPVC (all boilers)

- PP(s) (WB2B 80, 105, B2HA 80, 88, 100, 112, 150

only)

Caulk here

(exterior caulking)

Legend

Support system

Exhaust vent termination

Combustion air intake (left, right or through co-axial

opening), remove and discard air intake cover

(WB1B 26, 35, B2TA 19, 35, B2TB 19, 35,

WB2B 19, 26, 35, B2HA 19, 28, 35, B2HB 19, 26, 35)

Combustion air opening

a Equivalent vent length (exhaust)

Summary of Contents for Vitodens 100-W WB1B Series





























































































Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews:

Viessmann Vitodens 100-W WB1B Series, Installation Instructions Manual, Page: 66 / 92

Search results

Summary of Contents for Vitodens 100-W WB1B Series

Reviews: