Viessmann Vitocal 242-S Installation And Service Instructions Manual Download Page 54

Page: 54 / 152

Terminals

Function

Explanation

X3.1

Switched phase.

Via control unit ON/OFF switch.

Note
Observe the total load (1000 W) of all con-
nected components.

X3.3
X3.4

Flow limiter

Requires zero volt

N/O

contact:

■ Closed: Heat pump in operation
■ Open: Heat pump shut down
■ Breaking capacity 230 V, 015 A

Remove jumper when making this connec-
tion.

X3.6
X3.7

Power-OFF (factory-fitted
jumper).

Requires zero volt

N/C

contact:

■ Closed: Heat pump in operation
■ Open: Heat pump shut down
■ Breaking capacity 230 V, 0.15 A

Remove jumper when making this connec-
tion.

Note
■ No parameters need to be set.
■ The compressor is "forced" off as soon

as the contact opens.

■ The supply voltage to the respective

components is switched off by the pow-
er-OFF contact signal.

■ For the instantaneous heating water

heater, the stages to be switched off can
be selected (parameter "Output for in-
stant. heating water heater at power-
OFF 790A").

■ For further information regarding power-

OFF, see chapter "Power supply".

Installation sequence

Electrical connection

(cont.)

5623 661 GB

Summary of Contents for Vitocal 242-S

























































































































































Search results

Summary of Contents for Vitocal 242-S

Reviews:

Related manuals for Vitocal 242-S

Brands by name

Popular brands

Viessmann Vitocal 242-S, Installation And Service Instructions Manual

Search results

Summary of Contents for Vitocal 242-S

Reviews:

Related manuals for Vitocal 242-S

Brands by name

Popular brands