Viessmann CM2 500 Installation Instructions Manual Download Page 32 | Manualshive

Page: 32 / 50

background image

32

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Boiler Piping in Heating / Cooling Application

Legend

A

System supply

B

System return

C

Valve

D

Flow check valve

E

Circulation pump

F

Automatic feed valve

G

Pre-charged expansion tank

The boiler, when used in connection with a refrigeration

system, must be installed so that the chilled medium is

piped in parallel to the boiler and with appropriate valves

to prevent the chilled medium from entering the boiler.
The boiler piping system of a hot water heating boiler is

connected to the heating coils located in the air handling

units. The boiler piping system may be exposed to

refrigerated air circulation and must be equipped with

flow control valves or other automatic means to prevent

gravity circulation of the boiler water during the cooling

cycle.
Check the installation instructions of the chiller

manufacturer carefully for additional requirements.

Cooling season starts:

Close valve V1 and open valve V2.

Heating season starts:

Close valve V2 and open valve V1.

Metal tags labelling these valves should be attached.

IMPORTANT

In the above system, the circulating pump must be

operated from a separate on/off switch - not from the

boiler control.

Heating /

Cooling unit

Heating /

Cooling unit

Heating /

Cooling unit

Water

Chiller

Boiler

«
...
30
31
32
33
34
...
»

Summary of Contents for CM2 500



















































Reviews:

No comments

Related manuals for CM2 500

Brand: Alpha Pages: 4

Brand: Effecta Pages: 24

Brand: Slant/Fin Pages: 4

Brand: Watts Pages: 25

Brand: Beretta Pages: 60

Mini-Boiler EMB-W-9

Brand: Electro Industries Pages: 23

Electro-Boiler EB-WO-13

Brand: Electro Industries Pages: 28

Brand: HTP Pages: 91

Brand: Truma Pages: 28

Gold 15 Heat ErP

Brand: Potterton Pages: 16

LOGIC MAX COMBI 2 C24

Brand: Ideal Heating Pages: 68

Classic FF 340 LF

Brand: Ideal Boilers Pages: 40

Brand: Viessmann Pages: 32

Brand: Harman Pages: 24

Brand: Baxi Potterton Pages: 12

Brand: Kabola Pages: 20

FT Combi Series

Brand: Laars Pages: 12

Brand: Worcester Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands