Viessmann CM2 500 Installation Instructions Manual Download Page 18

Page: 18 / 50

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Rails and Supports

1. Insert four M6 x 10 screws halfway into each side

of the top and base frame.

2. Hook the top LH and RH rails onto the top frame

using the keyholes.

3. Hook the bottom LH and RH rails onto the base

frame, so that the rails protrude to the rear.

4. Make sure the top rails are aligned at the front

(see

). Then tighten all screws to secure each rail.

5. Install bottom plate brackets using two M6x15 screws

per bracket. Pre fit the side and top panels to allow

for rail alignment. Once rails are aligned, remove the

side and top panels and tighten screws (see pages 18

and 27 for panel installation).

Legend

Rail alignment

Rails on top frame

Rails on base frame

Body supports (included with the boiler)

Boiler

Side Panels

Legend

Side panel, front

Side panel, centre

RH rear side panel

Note:

Adjust the side panels to line up with the front

panel

before securing with screws.

1. Install left center side panel

. Observe aligning

notches and cutouts.

2. Install right center side panel

. Observe aligning

notches and cutouts.

3. Install right front side panel

. Observe aligning

notches and cutouts.

4. Install left front side panel

. Observe aligning

notches and cutouts.

5. Install rear left side panel

. Observe aligning

notches and cutouts.

6. Install right rear side panel

. Observe aligning

notches and cutouts.

7. Secure side panels to the top rails with two 2.8 mm

screws per panel.

LH rear side panel

Side panel, centre

Side panel, front

Summary of Contents for CM2 500



















































Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands

Viessmann CM2 500, Installation Instructions Manual

Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands