Viessmann CM2 500 Installation Instructions Manual Download Page 43

Page: 43 / 50

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Venting

The venting system must be securely supported by a

support system suitable for the weight and design of

the materials employed. Contact your vent material

supplier for more information specific to your installation.
Supports are used to transfer the weight of an installation

to the building structure. There are different types of

supports and their capacity varies with each type and

diameter.
The following support types are available at your local

vent material supplier:



anchor plate



wall support



roof support



floor support



suspension band (hanger).

Installation of Support System - PP

IMPORTANT

Bracing

Contact your local vent material supplier for more

information specific to your installation. Braces are

required to stabilize an installation. There are different

types and their use and spacing vary.
The following types of braces are available at your local

vent material supplier:



wall band



wall band extension



guy wire band



roof brace.

Ensure that the venting system is properly supported;

the boiler is not designed to support the weight of the

venting system.

Vent system suppliers

To order approved PP(s) vent system contact the following

suppliers.

M&G / Duravent

Tel. 800-835-4429

Tel. 518-649-9700

Fax: 518-463-5271

[email protected]

www.duravent.com

Centrotherm InnoFlue

Eco Systems. L.L.C.

Tel. (877) 434-3432

Fax. (518) 618-3166

Email: [email protected]

Web: www.centrotherm.us.com

IMPORTANT

For exhaust vent pipe material:

Use only ULC S-636 / UL 1738 vent material.

Long Sweep Elbows

Material

elbow equivalent length

ft. (m)

elbow equivalent length

ft. (m)

elbow equivalent length

ft. (m)

Stainless steel

3 (0.91)

2 (0.61)

---

CPVC plastic pipe

5 (1.52)

3 (0.91)

---

1 (0.30)

1.6 (0.50)

Standard long sweep elbow equivalent length material

Note:

If flexible vent or air-intake pipe are used, the total max. equivalent length will be reduced by 25% [150 ft. (45 m)].

Summary of Contents for CM2 500



















































Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands

Viessmann CM2 500, Installation Instructions Manual

Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands