Viessmann CM2 500 Installation Instructions Manual Download Page 37

Page: 37 / 50

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Venting

General Venting Information

(continued)

Flashing and storm collar installation

Flashings and storm collars are field supplied. Flashings

and storm collars suitable for Type B vent materials (or

better) may be used.
To obtain flashings and storm collars, please contact

your local vent material supplier. Follow the installation

instructions supplied by the special venting manufacturer.
Follow local codes to properly isolate the exhaust vent

pipe when passing through floors, ceiling and roof.
Always check the marking on the pipe to make sure you

are using the correct material.

Additional Requirements for Stainless Steel Vent Pipe Material

Use stainless steel venting system (UL/ULC listed for

category IV) for horizontal or vertical venting of the

Vitocrossal boilers.

Contact one of the suppliers (see listing on right) to order.
Prior to installation, check that the correct single-wall

vent parts were ordered and supplied.

Exhaust vent/air intake connection to boiler

The vent connection to the Vitocrossal boiler must be

made with the starter stainless steel adaptor (supplied

by others).
Combustion air intake, flex hose and adaptor must be

installed. If using room air-independent venting system,

connect the air intake pipe (from outdoors)to the adaptor

provided. If room air-dependent venting system is used,

the air is drawn into the burner inlet through adaptor and

flexible pipe. (See figure from page 11 and 17).

For exhaust vent pipe material:

Do not use any other vent material.

IMPORTANT

Note:

For SS venting system order transition adaptors

from the above mentioned suppliers.

WARNING

The use of vent material other than listed UL/ULC

stainless steel and PPs positive pressure vent pipe and

fittings can cause property damage, severe personal

injury and/or loss of life.

M&G / Duravent

Tel. 800-835-4429

Tel. 518-649-9700

Fax: 518-463-5271

Email: [email protected]

Web: www.duravent.com

ICC - Industrial Chimney Co.

400 J-F Kennedy,

St-Jerome, Quebec

Canada, J7Y 4B7

Tel. 514-565-6336

Fax: 514-565-6519

Email: [email protected]

Selkirk Canada Corporation

375 Green Road

Stoney Creek, ON L8E 4A5

Tel.: (905) 662-6600

Fax: (905) 662-5352

(US) 1-800-992-8368

(Canada) 1-888-735-5475

Email: [email protected]

Web: www.selkirkchimney.com

Novaflex

1-20 East Pearce St.,

Richmond Hill, Ontario,

Canada, L4B 1B7

Tel. 905-731-9411

Email: [email protected]

Security Chimneys

International Ltd.

2125 Rue Monterey,

Laval, Quebec H7L 3T6

Tel. 450-973-9999

(US) 1-800-361-4909

(Canada) 1-800-667-3387

Fax: 450-973-2222

Email: infoeng@

securitychimneys.com

Web: www.securitychimneys.com

Enervex Inc.

(formerly Exhausto)

Tel: 770-587-3238

Fax: 770-587-4731

(800) 225-2923

Email: [email protected]

Web:www.vpstack.com

Wesmech Technical Sales

50 Ronson Drive, Suite 160

Toronto, ON M9W 1B3

Tel.: (416) 251-8990

Fax: (416) 251-8900

1-800-613-3789

Email: [email protected]

Web: www.wesmechtech.com

Van-Packer Co. Inc.

302 Mill Street

PO Box 307

Buda, IL 61314

Tel.: (309) 895-2311

Fax: (309) 895-3891

1-888-877-8225

Email: [email protected]

Web:www.vpstack.com

Summary of Contents for CM2 500



















































Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands

Viessmann CM2 500, Installation Instructions Manual

Search results

Summary of Contents for CM2 500

Reviews:

Related manuals for CM2 500

Brands by name

Popular brands