Viessmann CM2 500 Installation Instructions Manual Download Page 29 | Manualshive

Page: 29 / 50

background image

29

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Boiler

Gas Flue Adaptor

1. Fully insert flue gas adapter inside the flue outlet

(if used with stainless steel piping).

Note:

Connect the flue outlet with the flue pipe

via the shortest possible run, with slight rise

(min

3

o

). Avoid sharp bends.

2. Connect flue system. Size: 10 in. (250 mm).

Note:

Support all venting components; make all

connections free of load and torque stresses.

The venting system must be securely

supported by an anchoring system as outlined

by the venting manufacturer.

IMPORTANT

The boiler flue gas collector vent is not designed to

support the weight of the venting system.

Control Panel and Covers

1. Plug in control interface cable and install cover.

2. Install control cosmetic cover.

3. Install buffer panel to the top rail and secure with

4.8 mm metal screws.

Legend

A

Control interface with cover

B

Buffer panel

C

Cosmetic cover

Note:

The flue gas adaptor is not included with the boiler

and if required must be supplied by the venting

manufacturer.

«
...
27
28
29
30
31
...
»

Summary of Contents for CM2 500



















































Reviews:

No comments

Related manuals for CM2 500

Brand: Ideal Boilers Pages: 4

Brand: U.S. Boiler Company Pages: 8

Brand: U.S. Boiler Company Pages: 60

Brand: U.S. Boiler Company Pages: 100

Brand: U.S. Boiler Company Pages: 56

Brand: U.S. Boiler Company Pages: 60

Brand: IBC Pages: 4

Brand: Steco Pages: 28

Brand: Garland Pages: 12

Brand: CTC Union Pages: 50

Brand: U.S. Boiler Company Pages: 72

Brand: PROBOIL Pages: 44

Brand: Ravelli Pages: 200

Brand: ferolli Pages: 124

Brava One 40 BF

Brand: Sime Pages: 100

Brand: Harman Stove Company Pages: 40

Lynx Electronic

Brand: Potterton Pages: 4

Brand: Ideal Boilers Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands