VESDA VESDA-E VES-A00-P Product Manual Download Page 62

Page: 62 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

5.5

Configuration Options

The VESDA-E VES-A00-P detector can be configured using the Xtralis VSC software.

The following sections describe the configuration options available in Xtralis VSC.

5.5.1

General Options

The General options include some basic identification information for the detector.

Figure 5-12: General Options

The General configuration options for the detector are as follows:

Network Name:

The name of the VESDAnet network. (The user can leave this blank if desired.).

Location:

A description of the physical location of the detector. This name will appear on Xtralis VSC

and on the LCD display of the A10 model detector.

Serial Number:

The serial number of the device. This is factory set and cannot be changed.

VESDA Zone:

The unique zone number used to link this detector and remote display/relay devices or

remote relay which output alarm and trouble status for this detector to the Fire Alarm Control Panel.

Authentication

Change Password:

The password used to authenticate Ethernet and WiFi access. Refer to Section

5.3.1 on page 52 for further information.

Summary of Contents for VESDA-E VES-A00-P





























































































































Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands

VESDA VESDA-E VES-A00-P, Product Manual

Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands