background image

Product Guide

Model 12201777

Tools needed for assembly:

Phillips Screwdriver
Pliers

FOR OUTDOOR USE ONLY

CAUTION:

Read and follow all safety statements, assembly 
instructions, and use and care directions before 
attempting to assemble and cook.

INSTALLER/ASSEMBLER:

Leave this manual with consumer.

CONSUMER:

Keep this manual for future reference.

WARNING:

Failure to follow all manufacturer’s instructions could 
result in serious personal injury and/or property 
damage.

CAUTION:

Some parts may contain sharp edges.   Wear 
protective gloves if necessary.

WARNING:

CARBON MONOXIDE HAZARD

Burning charcoal indoors can kill you. It gives off 
carbon monoxide, which has no odor. NEVER burn 
charcoal inside homes, vehicles, or tents.

CAUTION:

THIS UNIT IS HEAVY!

 

DO NOT

 attempt to 

assemble without a helper.

If you have questions or need assistance during assembly, please call 

.

To insure your satisfaction and for follow-up service,

 

register your appliance online at

 www.charbroil.com/register

1-800-241-7548

42804938 - 01/03/12

32 in. Barrel
Charcoal Smoker 
with Offset Chamber.

Summary of Contents for 12201777

























Reviews: