VESDA VESDA-E VES-A00-P Product Manual Download Page 43 | Manualshive

Page: 43 / 124

background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

37

4.3.6

Relays

The relays, located on the main processor card, interface to the Fire Alarm Control Panel (FACP) to
communicate faults, alarms and disabled states. The relays can be programmed using Xtralis VSC. Relays 3
and 6 are permanently set for Urgent Fault and Fire 1 respectively. Table 4-22 below illustrates the default
assignments of functions (conditions) to relays and summarizes the default behavior of each relay. Section
5.5.12 describes how to configure the relay behavior using Xtralis VSC. It is possible to assign more than one
condition to a relay.

Fire 1 Relay

If a detector relay is to be used to signal fire alarm to the Fire Alarm Control Panel (FACP) then the Fire 1 relay
must be used.

Urgent Fault and Fire 1 Relay Terminals

The Urgent Fault relay is energized during normal operation while the Fire 1 relay is only energized when a Fire
1 is detected. The operation of these two relays is summarized in the following table.

Table 4-1: Urgent Fault and Fire Relay Operation

URGENT FAULT Relay

Fire 1 Relay

No Fault

(Energized)

Fault

or unpowered state

No Fire

(De-energized)

Fire

Relay Assignments and Behaviour

l

Relays 1, 2, 4, 5, 7, 8, 9, 10, 11, 12 are fully configurable.

l

Relays 3 and 6 are fixed to Urgent Fault and Fire 1 respectively. These relays may be assigned additional
conditions.

l

Relays 3 and 6 are changeover relays. (SPDT (1 Form C)) All the other relays are single pole single throw
(SPST-NO (1 Form A)).

Relay #

Default

Assignment

Default to

Normally

Energized

Description for default configuration

Configurability

1

Disable

(Isolate) and

Standby

No

Energizes when an operator disables
(isolates) the detector. Also energizes when
the operator puts the detector into Standby
mode.

Fully

configurable

2

Minor Fault

Yes

De-energizes when a Minor Fault is
detected.

Fully

configurable

3

Urgent Fault

Yes

De-energizes when an Urgent Fault is
detected.

Note that Relay 3 is fixed Normally
Energized in order to ensure that a fault will
be signaled when power to the VES-A00-P
is removed. See Table 4-1.

Urgent Fault

cannot be

removed. Other

conditions can

be added.

Fixed Normally

Energized

4

Alert

No

Energizes when the Alert alarm is initiated.

Fully

configurable

Table 4-2: Default Relay Assignments

«
...
41
42
43
44
45
...
»

Summary of Contents for VESDA-E VES-A00-P





























































































































Reviews:

No comments

Related manuals for VESDA-E VES-A00-P

Brand: Falcon Pages: 7

Brand: jablotron Pages: 2

Brand: Ultra Start Pages: 8

Brand: Visonic Pages: 6

Brand: Kenmore Pages: 40

Brand: Trevi Pages: 8

Brand: Somogyi Pages: 11

Brand: Somogyi Pages: 11

Brand: Brennwagen Pages: 13

Brand: ADE Pages: 134

Brand: DEI Pages: 20

Brand: Avital Pages: 6

Brand: Cair Pages: 2

Brand: Zeon Pages: 10

Brand: Hama Pages: 24

Brand: Quebic Industries Pages: 11

Executive VIP 4000

Brand: Omega Research & Development Pages: 5

Brand: TEC Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands