VESDA VESDA-E VES-A00-P Product Manual Download Page 47 | Manualshive

Page: 47 / 124

background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

41

4.4

Powering Up

After installing the detector it is necessary to power up the system. The power up sequence lasts
approximately 15 seconds.

The VES-A00-P detector does not have a power switch i.e it is an "always on" device which is activated by
applying powered cabling to the power input terminal on the main board (Figure 4-33). This process must only
be performed by Xtralis accredited personnel.

If the system fails to power up, check all power wires are secured to their terminals and that the polarity is
correct.

On power up:

l

The Power LED illuminates and the detector runs a series of self-diagnostic tests.

l

If there is a fault, the Fault LED illuminates. To identify the fault, check the Active Event List for the
detector using Xtralis VSC.

l

The aspirator starts up and air may be felt flowing out of the exhaust port.

It is normal for the detector to display airflow faults immediately after the first power up and until the air flow
normalization step is done. Reset the detector by pressing the reset button on the front of the unit. This will
unlatch the relays and turn off the Fault LED. Any remaining faults will cause the Fault LED to illuminate
again. Proceed with the preliminary system check.

«
...
45
46
47
48
49
...
»

Summary of Contents for VESDA-E VES-A00-P





























































































































Reviews:

No comments

Related manuals for VESDA-E VES-A00-P

Brand: KEETEC Pages: 2

Brand: Nittan Pages: 18

MED 6000 Series

Brand: A.E.B. Pages: 46

ASTRA 777 Mobile

Brand: Scytek electronic Pages: 28

Brand: Majestic Pages: 16

Brand: SOUNDMASTER Pages: 74

Brand: Uniden Pages: 8

Brand: jablotron Pages: 2

Brand: Flammex Pages: 40

Fire-Lite SD350

Brand: Pittway Pages: 2

Brand: iCES Pages: 4

Brand: Vanderbilt Pages: 5

Brand: Fire-Lite Alarms Pages: 2

Brand: Naxa Pages: 10

Brand: CrimeStopper Pages: 1

Brand: CrimeStopper Pages: 7

POWERCLOCK iBT235

Brand: iHome Pages: 10

Brand: iHome Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands