manualshive.com logo in svg

VESDA VESDA-E VES-A00-P, Product Manual

The VESDA VESDA-E VES-A00-P product manual is available for free download on our website. This comprehensive manual ensures that you have all the necessary information to efficiently operate your VESDA VES-A00-P unit. Simply visit manualshive.com to easily access and download the user manual now.

Share
Download
background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

iii

Codes and Standards Information for Air Sampling Smoke Detection

We strongly recommend that this document is read in conjunction with the appropriate local codes and standards
for smoke detection and electrical connections. This document contains generic product information and some
sections may not comply with all local codes and standards. In these cases, the local codes and standards must
take precedence. The information below was correct at time of printing but may now be out of date, check with your
local codes, standards and listings for the current restrictions.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one
or more of the following measures; re-orientate or relocate the receiving antenna, increase the separation between
the equipment and receiver, connect the equipment to a power outlet which is on a different power circuit to the
receiver or consult the dealer or an experienced radio/television technician for help.

FDA

This Xtralis product incorporates a laser device and is classified as a Class 1 laser product that complies with FDA
regulations 21 CFR 1040.10. The laser is housed in a sealed detector chamber and contains no serviceable parts.
The laser emits light which can be hazardous to the eye. Under no circumstances should the detector chamber be
opened.

The laser chamber is identified by the labels shown below:

DANGER

DO NOT OPEN

NO SERVICEABLE

PARTS

Laser Radiation when Open
AVOID DIRECT EXPOSURE TO BEAM

NE PAS OUVRIR

DISPOSITIFS/PIECES

NON ECHANGEABLES

Rayonnement Laser en cas d’ouverture

EVITEZ TOUTE EXPOSITION DIRECTE AU FAISCEAU

CLASS 1

LASER PRODUCT

PRODUIT LASER

DE CLASSE 1

AS1603.8

The performance of this product is dependent upon the configuration of the pipe network. Any extensions or
modifications to the pipe network may cause the product to stop working correctly. All pipe network designs must be
validated using ASPIRE. ASPIRE is available from your authorized representative.

The product is not intended to be mounted in hostile environments but is able to sample from hostile environments.

AS1851.1 2005

Maintenance Standards. Wherever this document and the AS1851.1 differ, AS1851.1 should be followed in
preference to this document.

Summary of Contents for VESDA-E VES-A00-P





























































































































Reviews:

No comments

Related manuals for VESDA-E VES-A00-P

La Crosse Technology C85135 Faqs preview
C85135
Brand: La Crosse Technology Pages: 9
La Crosse Technology C83117 Manual preview
C83117
Brand: La Crosse Technology Pages: 10
La Crosse Technology 617-1270 Faq preview
617-1270
Brand: La Crosse Technology Pages: 5
La Crosse Technology 616A-1908 Faqs preview
616A-1908
Brand: La Crosse Technology Pages: 4
La Crosse C89201 User Manual preview
C89201
Brand: La Crosse Pages: 6
Tanda TX7100 Installation And Operation Manual preview
TX7100
Brand: Tanda Pages: 9
Excalibur RF-51-eDp Operation Manual preview
RF-51-eDp
Brand: Excalibur Pages: 20
Omega Excalibur ATV-1000 Manual preview
Excalibur ATV-1000
Brand: Omega Pages: 34
Kidde TRUSENSE SMOKE 2050-DS10 User Manual preview
TRUSENSE SMOKE 2050-DS10
Brand: Kidde Pages: 28
Velleman K3504 Illustrated Assembly Manual preview
K3504
Brand: Velleman Pages: 16
La Crosse Technology 616-30357 Setup Manual preview
616-30357
Brand: La Crosse Technology Pages: 13
oklahoma joes Longhorn 13201747 Product Manual preview
Longhorn 13201747
Brand: oklahoma joes Pages: 16
Kidde Fire Systems SmartOne KS-PS Manual preview
SmartOne KS-PS
Brand: Kidde Fire Systems Pages: 4
Audiovox 1287180 Owner'S Manual preview
1287180
Brand: Audiovox Pages: 12
Audiovox 1285757A Owner'S Manual preview
1285757A
Brand: Audiovox Pages: 10
CrimeStopper CS-2002DC Series III Installation And Operating Instructions Manual preview
CS-2002DC Series III
Brand: CrimeStopper Pages: 21
Equity NIGHT VISION 30330B Manual preview
NIGHT VISION 30330B
Brand: Equity Pages: 2
Sharper Image SI615 Instructions Manual preview
SI615
Brand: Sharper Image Pages: 16

Brands by name

Popular brands

Load more brands