background image

 
 
 
 
 
 

 

  CS-2002DC Series III 

 

 

 

REMOTE CONTROL ALARM SYSTEM 

 

 

INSTALLATION & OPERATING INSTRUCTIONS 

 

 

 

INTRODUCTION 

 
 

CONGRATULATIONS

 on your choice of a Gargoyle™ Remote Alarm System by Crimestopper Security 

Products Inc.  This booklet contains the information necessary for installing, using, and maintaining your alarm 
system.  If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the 
Tech Support number below. 

 

*IMPORTANT INFORMATION: Primary and Optional Features:

 

-PRIMARY:

  These are features that must be connected in order for the system to operate properly; i.e. the 

Siren, L.E.D., +12V Power, Ground, Doorpin, Override/Program/Valet Button etc. 

 

-OPTIONAL:

  These are features to be connected if desired or agreed upon by the installing dealer. These 

features may also require additional parts and/or labor fees.  Consult with your installer beforehand; i.e. Door 
Locks, Flashing Lights, Starter disable, Hood/Trunk trigger, and Auxiliary Remote Outputs etc. 

 

This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: 1) This device may not cause interference,
and (2) this device must accept any interference that may be received,
including interference that may cause undesired operation.  The
manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.

 

 

 

    TECH SUPPORT 

Mon-Fri 8:00 AM-4:30 PM Pacific Time 

        (800) 998-6880 

 
 
REV. B 4/2003 

SW: H5 

Summary of Contents for CS-2002DC Series III






















Reviews: