CrimeStopper CS-2002DC Series III Installation And Operating Instructions Manual Download

Page: 2 / 21

TABLE OF CONTENTS

Installation Cautions & Warnings…….……………………………….………………………………………………2

Control Module & Component Mounting……………...………………………..……………………….…………..3

Wiring……..……………………………………………………………………………………………………….…….3-6

Parking Light Jumper Diagram………………………………………………….………………………….…..……..5

Power Door Lock Wiring……………………………………………………….………..………………….…..……6-8

Transmitter Programming………………………………………………………………………………………………9

Option Programming…………………………………………….……………………………….………….….…10-12

Programmable Option Reset………………………………….……………………………….……………..………13

Custom Personal Override Code…………..………………….……………………………….……………………13

Remote Control Diagram…………...……………..……………………………………………………….………….14

Operating Instructions………………………..……………………………………………………………..…….14-17

2 Vehicle Operation……….……………………………………………………………………………………………17

Car Jack Protection Features…………..…………………………………………………………………….………18

LED, Shock Sensor & System Wiring Diagram………………………………………………………..………19-20

INSTALLATION CAUTIONS & WARNINGS

BEFORE BEGINNING

, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR

BAGS, ABS BRAKES, ENGINE COMPUTERS, BATTERY etc.).

WE RECOMMEND

the use of a VOLT/OHM METER to test and verify wiring circuits. Test lights or illuminated

probes can cause damage to on-board computer or engine management systems.

DO NOT exceed maximum output ratings.

WE RECOMMEND that the MAIN SYSTEM FUSE be REMOVED

before jump starting, using a battery

charger, or changing the battery. A voltage surge or high boost condition could damage alarm circuits.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED

with brake, and gas pedals, steering

column, or any other moving parts in the vehicle.

Summary of Contents for CS-2002DC Series III






















Search results

Summary of Contents for CS-2002DC Series III

Reviews:

Related manuals for CS-2002DC Series III

Brands by name

Popular brands

CrimeStopper CS-2002DC Series III, Installation And Operating Instructions Manual

Search results

Summary of Contents for CS-2002DC Series III

Reviews:

Related manuals for CS-2002DC Series III

Brands by name

Popular brands