background image

 FSDR-XXX, SEFSDR-XXX,

 AND SSFSDR-XXX MODELS

1

2

 Hour Fire & Combination Fire 

Smoke Dampers

 

Vertical and Horizontal Mount

Part #461868

SAFEty WARNING:

 

Improper installation, adjustment, alteration, 
service or maintenance can cause property damage, 
injury or death. Read the installation, operating, 
and maintenance instructions thoroughly before 
installing or servicing this equipment.

This manual is the property of the owner, and is required 
for future maintenance. Please leave it with the owner 
when the job is complete.

WARRANty

Greenheck warrants this equipment to be free from 
defects in material and workmanship for a period of one 
year from the purchase date. Any units or parts which 
prove to be defective during the warranty period will 
be repaired or replaced at our option. Greenheck shall 
not be liable for damages resulting from misapplication 
or misuse of its products. Greenheck will not be 
responsible for any installation or removal costs. 
Greenheck will not be responsible for any service work 
or backcharges without prior written authorization. 

Due to continuing research, Greenheck reserves the right to change specifications without notice.

“UL CLASSIFIED (see complete marking on product)”

“UL CLASSIFIED to Canadian safety standards (see 

complete marking on product)”

 

UL Standard 555 & 555S (Classification #R13317)

FSDR-XXX, SEFSDR-XXX, and SSFSDR-XXX Model 

Dampers are intended for installation in accordance with 

combination fire smoke damper requirements established 

by:

National Fire Protection Association 

    NFPA Standards 80, 90A, 92A, 92B & 101

BOCA  National Building Codes
ICBO  Uniform Building Codes
IBC International Building Codes  
SBCCI  Standard Building Codes
New york City 

(MEA listing #260-91-M)

RECEIVING AND HANDLING

Upon receiving dampers, check for both obvious and 
hidden damage. If damage is found, record all necessary 
information on the bill of lading and file a claim with 
the final carrier. Check to be sure that all parts of the 
shipment, including accessories, are accounted for.

Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust and the weather is highly 
recommended. Do not store at temperatures in excess of 
100°F.

Installation, Operation and Maintenance Instructions

Summary of Contents for FSDR-XXX








Reviews: