VERTO 51G452, Manual

Page: 8 / 52

8
GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
tel. + 48 22 573 0 3 85
Ul. Pograniczna 2 / 4 fax. + 48 22 573 0 3 83
0 2 - 285 Warszawa e-mail service@gtxservice.pl
Sieć Punktów Serwisowych do napraw gwarancyjnych
i pogwarancyjnych dostępna na platformie internetowej
gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl . Zeskanuj kod QR i wejdź:
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
WET/DRY BENCH GRINDER
51G452
CAUTION: BEFORE USING THE TOOL READ THIS MANUAL CAREFULLY
AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SAFETY CONDITIONS SPECIFIC FOR WET/DRY BENCH GRINDER
OPERATION
• Closely follow the instructions from wet/dry bench grinder manual.
• Do not use damaged grinding wheels.
• Use grinding wheels recommended by the manufacturer only, which
are labelled to work with the speed given on the wet/dry bench
grinder rating plate or higher.
• Adjust spark shield often enough to compensate wear of wheel to the
smallest possible distance between the wheel and the shield, however
not greater than
2 mm.
• Firmly fix all safety parts to the wet/dry bench grinder.
• Do not start grinding when there are no safety elements installed (use
shield when grinding).
• During operation use personal protection measures appropriate for
used machine (glasses or anti-splinter goggles, face shields, earmuff
protectors, protection half-mask, safety shoes, protective gloves and
other pieces of protective clothing).
• You can proceed only with such type of grinding that the grinding
wheel is designed for (consider limitations of application, safety
regulations and other information).
• Always unplug the power cord from mains socket before commencing
any activity related to adjustment, maintenance, or grinding wheel
replacement.
• Always ensure that eye shields attached to bench grinder are correctly
positioned.
• When the wet/dry bench grinder is not being used, it should be
switched off. Never leave the wet/dry bench grinder unattended if it
is not switched off and the plug is not removed from mains socket.
Never leave the wet/dry bench grinder unattended before grinding
wheels are stopped completely.
• Do not use grinding wheels with maximum allowable rotational
speed lower than
295 0 rpm or wet grinding wheel with maximum
allowable speed lower than 1 34 rpm.
• Persons below 1 8 years old cannot use the wet/dry bench grinder.
• Do not leave cloths, pieces of garment, ropes, cords and other similar
objects in proximity of the wet/dry bench grinder.
• When someone distracts you when you are using the wet/dry bench
grinder, end the operation and switch the wet/dry bench grinder off.
• Occasionally check that all nuts, bolts and other fixing elements are
properly fastened and secured.
• Do not over-fasten nuts that fix grinding wheels.
• Do not use grinding wheel that has been hit, especially side surface.
• Replace wheel that is cracked or suspected to be damaged.
• After installation of new grinding wheel always allow it to rotate for few
minutes at full rotational speed prior to operation. During the wet/dry
bench grinder start-up, its operator should stand at side of it.
• Prior to every start up of the wet/dry bench grinder ensure the
grinding wheels can rotate freely.
• Do not use the wet/dry bench grinder until all shields are fixed and
secured appropriately.
• Prior to starting operation ensure tool support is appropriately set.
• Do not overload the wet/dry bench grinder. Allow the wet/dry bench
grinder to work at full rotational speed or at speed close to maximum.
• Never apply excessive pressure on grinding wheel. It may crack and
cause operator body injury.
• Do not use the wet/dry bench grinder for cutting.
• Prior to starting the wet/dry bench grinder ensure the grinding
wheels have no contact with processed material.
• For wheel dressing and cleaning use only the tools designed for such
purpose.
GB