Velatia ORMAZABAL gae.630 Manual Download

Page: 56 / 64

IG-322-EN version 03; 22/07/2022

Maintenance

General instructions

-insulated circuit-breaker panel:

Type

gae

.630 -1LSV(G)-/5/

in modular extensible design up to 24 kV, 20 kA

7.2.2. Maintenance

Prior to maintenance, electrically isolate and secure

the operating range in accordance with the “safety

rules” specified by DIN VDE/IEC.

Maintenance is to be performed:

• At an interval of 10 years after commissioning, If found

necessary during the inspection.

• If found necessary during the inspection.
• After each 2.000 cycles of operation.

7.2.3. Cleaning the circuit-breaker panel

If the circuit-breaker panel is operated under dirty

conditions or in aggressive air, the surfaces must be cleaned

during maintenance.

Before starting cleaning work the circuit-breaker panel

must be isolated.
To avoid unintended operation, the supply voltage is

to be shut down.

Cleaning is performed using the following procedure:

• Manually switch on and off circuit- breaker (spring

accumulator tension is released, switch position

indicator is in the “OFF” position).

• Switch on earthing switch
• Open the fasteners and remove the front covers

(if required).

Carefully clean off all dirt, especially from the surfaces of

insulating materials.

Clean off strongly adhesive, e. g. greasy, dirt with a lint-free

cloth soaked in a commercial detergent, then wipe off with

clear water and dry.

Do not use any aggressive solvents!

7.2.4. Scope of maintenance on the vacuum circuit-breaker’s mechanical drive groups

• Shut down motor winding (if fitted).
• On the circuit-breaker, actuate the ON and OFF

pushbuttons as follows: OFF-ON-OFF.

•  Remove the control panel cover.
•  Assess the overall condition of the operating mechanism.
•  Clean the surfaces with a soft, dry, lint-free cloth
•  To re-lubricate friction surfaces and bearings with resin-

and acid-free lubricants (see Chapter 8.9) please contact

our customer service department. Re-lubrication serves

to refresh the lubricant.

• The maintenance plan of the circuit breaker must be

performed to the three-phase vacuum circuit breaker

by specialists every 2000 operations.

• Re-fit the control panel cover.

In case of problems during the maintenance work

and in case of malfunctions, please contact the plant

where the unit was manufactured.

The following information is required on contacting the

manufacturer:

•  Type
•  Serial number
•  Year of manufacture

Summary of Contents for ORMAZABAL gae.630

































































Search results

Summary of Contents for ORMAZABAL gae.630

Reviews:

Related manuals for ORMAZABAL gae.630

Brands by name

Popular brands

Velatia ORMAZABAL gae.630, Manual

Search results

Summary of Contents for ORMAZABAL gae.630

Reviews:

Related manuals for ORMAZABAL gae.630

Brands by name

Popular brands