background image

User’s Guide ______________________________________________________________________

18 ___________________________________________________________________M211486EN-A

Ozone Sensor Unit

The ozone sensor unit is either of the following:

-

Science Pump Corporation (SPC) Model ECC-6A ozone sensor

-

Droplet Measurement Technologies (DMT) Model Z ozone sensor

The sensors are based on chemical reaction cells. The type of the 
sensors is electrochemical concentration cell (ECC). Air is sampled 
flow (by using a pump) and it goes to a reaction cell, in which the 
sampled ozone reacts in a solution, and the current developed in the 
reaction is detected and measured with an ozone interface. The ozone 
sensor units are thoroughly discussed in the sensor manufacturers’ 
manuals (see section 

Related Manuals on page 11

) and Performance 

Review Literature listed in Appendix D 

Performance Review Literature 

on page 119

.

The main parts of an SPC ECC-6A ozone sensor are seen in 

Figure 2 on 

page 19

. Model Z ozone sensor is similar to the SPC sensor. Refer to the 

sensor manufacturer’s manuals for more detailed information.

Summary of Contents for RS41





























































































































Reviews: