manualshive.com logo in svg

Vaisala RS41, User Manual

Share
Download
Vaisala RS41 User Manual Download Page 107

Chapter 6 _________________________________________________________  Technical Support

VAISALA______________________________________________________________________ 105

CHAPTER 6

TECHNICAL SUPPORT

This chapter presents information about technical support.

Product Returns

If the product is found faulty, please follow the instructions below to 
speed up the process and to avoid extra costs to you.

1.

Read the radiosonde warranty information.

2.

Contact Vaisala technical support via e-mail or fax and request for 
RMA (Return Material Authorization) and shipping instructions.

3.

Proceed as instructed by Vaisala technical support and provide the 
failure report as requested.

Technical Support

NOTE

RMA must always be requested from Vaisala technical support before 
returning any faulty material.

For technical questions, contact the Vaisala technical support:
E-mail

[email protected]

Fax

+358 9 8949 2790

Summary of Contents for RS41





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands