manualshive.com logo in svg

Vaisala RS41, User Manual

Share
Download
Vaisala RS41 User Manual Download Page 123

Appendix D ______________________________________________  Performance Review Literature

VAISALA______________________________________________________________________ 121

Smit, H.G.J., W. Straeter, B. 
Johnson, S. Oltmans, J. Davies, 
D.W. Tarasick, B. Hoegger, R. Stubi, 
F. Schmidlin, T. Northam, A.  
Thompson, J. Witte, I. Boyd, F. 
Posny 

Assessment of the performance of ECC-ozonesondes under 
quasi-flight conditions in the environmental simulation chamber: 
Insights from the Jülich Ozone Sonde Intercomparison 
Experiment (JOSIE), J. Geophys. Res., 112, D19306, 
doi:10.1029/2006JD007308. 2007

Smit, H.G.J. and D.Kley

Jülich Ozone Sonde Intercomparison Experiment (JOSIE) ; 
WMO Global Atmosphere Watch report series No. 130 
(Technical document No.926) WMO, Geneva, 1998.

Smit, H.G.J.& all

The 1996 WMO International intercomparison of ozonesondes 
under quasi flight conditions in the environmental simulation 
chamber at Jülich, Proceedings XVIII Quadrennal Ozone 
Symbosium, Eds. R. Bojkov, and G. Visconti, L'Aquila, Italy, 
Sept. 1996.

Smit, H.G.J. & all

The 1996-1999  Evaluation of Performance of ECC- Sondes 
Under Quasi-Flight Conditions in the Environmental Simulation 
Chamber, Proceedings of  Quadrennal Ozone Symbosium 
2000, Sapporo, Japan, July 2000. 
SPARC-IOC-GAW Assessment of Trends in the Vertical 
Distribution of Ozone (1998), SPARC Report No.1, WMO 
Global Ozone Research and Monitoring Project Report No. 43, 
World Meteorological Organization, Geneva. Note: In this report 
performance investigations made before 1996 have been 
intensively evaluated by the SPARC-IOC-GAW assessment 
panel

Stübi R., G. Levrat, B. Hoegger, P. 
Viatte, J. Staehelin, F. J. Schmidlin

In-flight comparison of Brewer-Mast and electrochemical 
concentration cell ozonesondes, J. Geophys. Res., 113, 
D13302, doi:10.1029/2007JD009091. 2008.

WMO 

Third WMO intercomparison of the ozonesondes used by the 
Global ozone observing System, Vanscoy Canada 13-24 May 
1991, WMO/ Global Atmosphere Watch/WMO Global Ozone 
Research and Monitoring Project, Report No 27.

Table 24

Performance Review Literature (Continued)

Name

Details

Summary of Contents for RS41





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands