manualshive.com logo in svg

Vaisala RS41, User Manual

Share
Download
Vaisala RS41 User Manual Download Page 122

User’s Guide ______________________________________________________________________

120 __________________________________________________________________M211486EN-A

Godson, W.L.

The representation and analysis of vertical distributions of 
ozone, Quarterly Journal of the Meteorological Society, Vol. 88, 
No. 377, July 1962.

Hoegger, B.A. & all

Contribution of Switzerland to International Ozonesonde 
Intercomparisons. Proceedings of GAW-CH Conference Zurich, 
14-15 October 1998. Swiss Agency for the Environment, 
Forests and Landscape (SAEFL), Environmental 
documentation No.110 Air, pp 43-47.

Johnson, Bryan J., Samuel J. 
Oltmans, H. Vomel, H.G.J. Smit, T. 
Deshler., and C. Kroger

Electrochemical concentration cell (ECC) ozonesonde pump 
efficiency measurements and tests on the sensitivity to ozone of 
buffered and unbuffered ECC sensor cathode solutions. J. 
Geophys. Res., 107 (D19), 4394, doi:1029/2001JD000557, 
2002.

Kerr, J.B. & all

The 1991 WMO international ozonesonde intercomparison at 
Vanscoy, Canada. Atmosphere Ocean, Vol XXXII, No 4 pp 685-
716, December 1994.

Kley, D., H.G.J. Smit, H. Vömel, H. 
Grassl, V. Ramanathan, P.J. 
Crutzen, S. Williams, J. Meywerk, 
S.J. Oltmans

Tropospheric water-vapour and ozone cross-sections in a zonal 
plane over the equatorial Pacific Ocean, Q.J.R. Meteorol. Soc. 
(1997), 123, pp. 2009-2040.

Komhyr, W.D.

Operations Handbook - Ozone Measurement to 40-km Altitude 
with 4A Electrochemical Concentration Cell (ECC) 
Ozonesondes (used with 1680-MHz radiosondes), NOAA 
Technical Memorandum ERL ARL-149,1986.

Komhyr, W.D., J.A. Lathrop, D.P. 
Opperman, R.A. Barns, and G.B. 
Brothers

ECC Ozonesonde performance evaluation during STOIC 1989, 
J. Geophys. Res., 100 9231-9244, 1995.

Komhyr, W.D.

Electrochemical Concentration Cell for Gas Analysis Ann. 
Geophys., t. 25, fasc. 1, 1969, pp. 203-210.

Schenkel, A., and B. Broder

Interference of some trace gases with ozone measurements by 
the KI method, Atmospheric Environment, 16, 2187-2190. 1982.

Schmidlin, F.J., B.A. Hoegger & all

Sondex96: A Field Experiment Conducted by NASA and SMI at 
Payerne,Switzerland. WMO Instruments and Observing 
Methods Report No 70, WMO Technical Conference on 
Meteorological and Methods of Observation (TECO-98), 
Casablanca Morocco, 13-15 May 1998, (WMO/TD No. 877), pp 
193-196.

Smit, H.G.J and ASOPOS panel

Quality assurance and quality control for ozonesonde 
measurements in GAW, WMO Global Atmosphere Watch 
Report series, No. 121, World Meteorological Organization, 
Geneva, 2013.

Smit, H.G.J.

Ozonesondes, in Encyclopedia of Atmospheric Sciences, 
edited by J. Holton, J. Pyle, and J. Curry, pp. 1469-1476, 
Academic Press, London. 2002.

Table 24

Performance Review Literature (Continued)

Name

Details

Summary of Contents for RS41





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands