Utax P-C2665 MFP User Manual Fax System Download

Page: 134 / 202

Setup and Registration

6-8

If user management or account management is
enabled, the login screen will appear. For the login
procedure, refer to

Account Management on

page 4-48

Press the





key to select [Fax].

Press the

key.

Press the





key to select [Transmission],

[Reception], [TX/RX Restrict.] or [TX/RX Common].

Configuring settings from [Transmission]

• Retry Times (page

6-13

)

• ECM TX (page

6-13

)

• TX Start Speed (page

6-13

)

Configuring settings from [Reception]

• Media Type for Print Output (page

6-14

)

• Rings (page

6-16

)

• Receiving Mode (page

6-17

)

• Reception Date/Time (page

6-18

)

• 2 in 1 Reception (page

6-19

)

• Print all at once [Batch Print] (page

6-20

)

• Procedure for receiving an encrypted

transmission (page

6-25

)

• Duplex Print Output (page

• ECM RX(page

• RX Start Speed(page

6-29

)

Configuring settings from [TX/RX Restrict.]

• Transmission Restriction (page

6-30

)

- Registering, changing, and deleting Permit fax

numbers (page

6-31

, page

6-32

)

- Registering, changing, and deleting Reject fax

numbers (page

6-34

, page

6-35

)

- Transmission restriction settings (page

6-38

)

- Reception restriction settings (page

6-39

)

- Registering, changing, and deleting Permit ID

numbers (page

- Checking and deleting the registered contents

of an encryption key (page

- Unknown Number Reception (page

6-39

)

Configuring settings from [TX/RX Common]

• Setting an encryption key for encrypted

transmission (page

6-22

)

Press the

key.

Move to the screen where you want to configure a
setting. (Follow the procedure in the explanation of
the setting.)

Summary of Contents for P-C2665 MFP











































































































































































































Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands

Utax P-C2665 MFP, User Manual Fax System

Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands