Utax P-C2665 MFP User Manual Fax System Download

Page: 151 / 202

Setup and Registration

6-25

Press the





key to select the desired

encryption key number.

Press the

key.

Press the





key to select [On] or [Off].

NOTE:

When the machine receives originals, the

encryption box is not used.

Press the

key. Proceed to the next step or step

15 when [On] or [Off] is selected in step 11,
respectively.

Use the numeric keys to enter the box number
(0000 to 9999).

Press the

key.

Press the

Start

key. The transmission will start.

NOTE:

When

is selected in

Destination Check

before Send

, a destination confirmation screen is

displayed when you press the

Start

key. For details,

refer to

Confirmation Screen of Destinations on

page 5-13

Operation at the Receiving System

To conduct encryption communication operating the receiving system, follow the steps below.

NOTE:

In encryption communication, sub address communication cannot be used.

Registering an

Encryption Key on page 6-22

Refer to

Basic Operation Procedure on page 6-7

Encryption Key:

*********************

*Key 02

Key 03

----------------

Encryption Box:

*********************

*Off

Box Number Entry:

(0000 - 9999)

****0000*

Summary of Contents for P-C2665 MFP











































































































































































































Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands

Utax P-C2665 MFP, User Manual Fax System

Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands