Utax P-C2665 MFP User Manual Fax System Download

Page: 131 / 202

Setup and Registration

6-5

Preparation:

Refer to

Receiving Mode on page 6-17

to select [Auto (TAD)].

The connected telephone set makes ringing tone
the set number of times.

NOTE:

If you lift the handset while the telephone set

is still making the ringing tone, the machine enters a
status the same as manual reception. (Refer to

Manual

Reception on page 4-11

The answering machine responds.

When the call is from a telephone, but the user
is absent

The answering machine plays a response
message, and starts recording the other party’s
message.

NOTE:

When silence continues for at least 30

seconds during recording, the machine switches to fax
reception.

When the call is from a fax

The machine starts receiving fax originals.

Summary of Contents for P-C2665 MFP











































































































































































































Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands

Utax P-C2665 MFP, User Manual Fax System

Search results

Summary of Contents for P-C2665 MFP

Reviews:

Related manuals for P-C2665 MFP

Brands by name

Popular brands