Unitech MS832 User Manual Download Page 60

Page: 60 / 135

Codabar

<Default All Codabar Settings>

Codabar On/Off

Codabar Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code.
You may either transmit, or not transmit Start/Stop characters.

Default = Don’t Transmit.

Codabar Check Character

Codabar check characters are created using different “modulos.” You can program the scanner
to read only Codabar bar codes with Modulo 16 check characters.

Default = No Check

Character

No Check Character

indicates that the scanner reads and transmits bar code data with or

without a check character.

When Check Character is set to

Validate and Transmit

, the scanner will only read Codabar

bar codes printed with a check character, and will transmit this character at the end of the
scanned data.

Summary of Contents for MS832






























































































































Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands

Unitech MS832, User Manual

Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands