Unitech MS832 User Manual Download Page 80

Page: 80 / 135

UPC-A Addenda Separator

When this feature is on, there is a space between the data from the bar code and the data from
the addenda. When turned off, there is no space.

Default = On

UPC-A/EAN-13
with Extended Coupon Code

Use the following codes to enable or disable UPC-A

and

EAN-13 with Extended Coupon Code.

When left on the default setting (

Off

), the scanner treats Coupon Codes and Extended Coupon

Codes as single bar codes.

If you scan the

Allow Concatenation

code, when the scanner sees the coupon code and the

extended coupon code in a single scan, it transmits both as separate symbologies. Otherwise,
it transmits the first coupon code it reads.

If you scan the

Require Concatenation

code, the scanner must see and read the coupon

code and extended coupon code in a single read to transmit the data. No data is output unless
both codes are read.

Default = Off

Summary of Contents for MS832






























































































































Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands

Unitech MS832, User Manual

Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands