Unitech MS832 User Manual Download Page 3 | Manualshive

Page: 3 / 135

background image

Copyright 2014 unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of unitech Electronics Co., Ltd.

Preface

About This Manual

Disclaimer

Unitech reserves the right to make changes in specifications and other information contained in
this document without prior notice, and the reader should in all cases consult Unitech to
determine whether any such changes have been made. The information in this publication
does not represent a commitment on the part of Unitech.

Unitech shall not be liable for technical or editorial errors or omissions contained herein: nor for
incidental or consequential damages resulting from the furnishing, performance, or use of this
manual.

This document contains propriety information that is protected by copyright. All rights reserved.
No part of this document may be photocopied, reproduced, or translated into another language
without the prior written consent of Unitech.

© 2013 Unitech. All rights reserved.

Trademarks

Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.
Other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies and are the property of their respective owners.

Regulatory Compliance Statements
FCC Warning Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference with radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference with radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

–  Reorient or relocate the receiving antenna.
–  Increase the separation between the equipment and receiver.
–  Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

«
1
2
3
4
5
...
»

Summary of Contents for MS832








































































































































Reviews:

No comments

Related manuals for MS832

Brand: Leuze Pages: 92

Brand: Icarus Pages: 59

Brand: Konica Minolta Pages: 153

NLS-NVH300 Series

Brand: Newland Pages: 322

Brand: Gemalto Pages: 9

Brand: Conrad Pages: 4

Brand: Sunstech Pages: 85

Brand: PAX Pages: 10

Brand: Y-E Data Pages: 27

Brand: SICK Pages: 122

CLV61 DualPort Series

Brand: SICK Pages: 114

Brand: Hand Held Products Pages: 64

Brand: Farpointe Data Pages: 2

Brand: Microdia Pages: 5

Brand: Wasp Pages: 40

Brand: ICT Pages: 38

Brand: Datalogic Pages: 19

Brand: Ratoc Systems Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands