Unitech MS832 User Manual Download Page 26 | Manualshive

Page: 26 / 135

background image

16

Copyright 2014 unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of unitech Electronics Co., Ltd.

Regular

is used when you normally have the Caps Lock key off.

Caps Lock

is used when you normally have the Caps Lock key on.

Shift Lock

is used when you normally have the Shift Lock key on (not common to U.S.

keyboards).

Automatic Caps Lock

is used if you change the Caps Lock key on and off.

The software tracks and reflects if you have Caps Lock on or off . This selection can only be
used with systems that have an LED that notes the Caps Lock status (AT keyboards).

Autocaps via NumLock

bar code should be scanned in countries (e.g., Germany, France)

where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works
similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the
Caps Lock.

«
...
24
25
26
27
28
...
»

Summary of Contents for MS832








































































































































Reviews:

No comments

Related manuals for MS832

Brand: CAB Pages: 10

Brand: Magtek Pages: 2

Interflex IF-73

Brand: Allegion Pages: 9

Brand: IEI Technology Pages: 41

Brand: Nedap Pages: 5

Brand: Digitus Pages: 11

Brand: Addonics Technologies Pages: 2

Brand: Sonnet Pages: 2

Brand: IDTECK Pages: 17

Brand: Unitech Pages: 169

Brand: Datalogic Pages: 16

DRAGON D Series

Brand: Datalogic Pages: 21

Brand: Unitech Pages: 8

Brand: Pocketbook Pages: 23

Brand: Pocketbook Pages: 45

Brand: Welch Allyn Pages: 68

SCANTEAM 3700 Wedge

Brand: Welch Allyn Pages: 100

SCANTEAM 3210 Series

Brand: Welch Allyn Pages: 145

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands