Unitech MS832 User Manual Download Page 16

Page: 16 / 135

Chapter 2

Programming the Interface

Introduction

This chapter describes how to program your system for the desired interface.

Programming the Interface - Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used interfaces.

Note: After you scan one of the codes, power cycle the host terminal to have the interface in

effect.

Keyboard Wedge

If you want your system programmed for an IBM PC AT and compatibles keyboard wedge
interface with a USA keyboard, scan the bar code below. Keyboard wedge is the default
interface.

Note: The following bar code also programs a carriage return (CR) suffix.

Laptop Direct Connect

For most laptops, scanning the

Laptop Direct Connect

bar code allows operation of the

scanner in parallel with the integral keyboard. The following

Laptop Direct Connect

bar code

also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 17).

Summary of Contents for MS832






























































































































Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands

Unitech MS832, User Manual

Search results

Summary of Contents for MS832

Reviews:

Related manuals for MS832

Brands by name

Popular brands