Unitech MS832 User Manual Download Page 28 | Manualshive

Page: 28 / 135

background image

18

Copyright 2014 unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of unitech Electronics Co., Ltd.

Default = Off.

Keyboard Modifiers

This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode.

C ASCII Mode On:

The scanner sends key combinations for ASCII control characters

for values 00-1F. Windows is the preferred mode. All keyboard country codes are supported.
DOS mode is a legacy mode, and it does not support all keyboard country codes. New users
should use the Windows mode. Refer to Keyboard Function Relationships, page 98 for CTRL+
ASCII Values.

Windows Mode Prefix/Suffix Off:

The scanner sends key combinations for ASCII control

characters for values 00-1F, but it does not transmit any prefix or suffix information.

Default = C ASCII Mode Off.

«
...
26
27
28
29
30
...
»

Summary of Contents for MS832








































































































































Reviews:

No comments

Related manuals for MS832

Brand: Wasp Pages: 27

4B-2044A Series

Brand: 4BARCODE Technology Pages: 39

Brand: Magtek Pages: 18

MultiReader PER3664BC

Brand: Prestigio Pages: 108

Brand: Cognex Pages: 17

Brand: Code Pages: 16

Brand: Clas Ohlson Pages: 4

Brand: Unitech Pages: 144

Brand: Roger Pages: 23

Brand: Magtek Pages: 61

PowerScan M8300

Brand: Datalogic Pages: 24

Brand: Stid Pages: 3

Brand: Stid Pages: 10

Brand: Albasca Pages: 52

Brand: Sunstech Pages: 37

Brand: Opticon Pages: 35

Scansteam 3400PDF

Brand: Welch Allyn Pages: 96

Brand: Manhattan Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands