30A135
7.)
CAREFULLY
position the
FILTER TUB COVER
on the
OPEN
end of the Filter Tub with the
SLOT
on the cover seated around the
Stand-pipe Handle Docking Assembly. Then,
SECURE
the cover to the standpipe assembly by locking the latch on the cover.
8.) Position the
ASSEMBLED
Filter Tub in front of the
FILTER TUB GUIDES
beneath the fryer; then
CAREFULLY
and
SLOWLY
insert the Filter Tub into the fryer using Standpipe Docking Handle Assy until the
MALE
In Line Plug on the Standpipe Docking
Handle Assembly seats in the
FEMALE
Bulkhead Coupling adjacent to the Drain Valve Assembly.
WARNING!!! TO ASSURE PRODUCING A QUALITY PRODUCT WHILE PROLONGING THE LIFE EXPECTANCY OF THE FRYER, ENSURE
FILTERING, BOIL-OUT AND CLEANING INSTRUCTIONS ARE STRICTLY ADHERED TO
.
d.
CLEANING THE FILTER TUB AFTER CLOSING
1.) “Micro Mesh” Stainless Steel Filter Screen:
Repeat
DAILY
steps 1 c page 29; then,
THOROUGHLY
clean the Filter Assembly as follows:
a)
THOROUGHLY
flush any remaining sediment from both sides of the filter screen with
HOT WATER.
b) Grasp the
FINGER LOOP
on
FRAME A
and adjacent
FINGER LOOP
on
FRAME B
,
EVENLY
pull the frames apart;
then
HINGE FRAME A
to remove it from the
FILTER SCREENS
FIRST.
c) Grasp the
FINGER LOOP
on the straight side of
FRAME B
; then
HINGE
it to remove
FRAME B
from the
FILTER
SCREENS
.
d) Separate the
UPPER
FILTER SCREEN
and
BAFFLE
from the
LOWER
FILTER
SCREEN.
e)
CAREFULLY
clean the two frames, screens and baffle in the 3 compartment sink with hot water and allow these
items to air dry.
DO NOT USE SOAP.
If necessary the channels in each frame can be cleaned with the edge of a
scotchbrite pad.
f) Insert the
SUCTION FITTING
on the BAFFLE in the hole of the
UPPER
FILTER SCREEN; then place these items
on top of the
LOWER
FILTER SCREEN.
g)
ENSURE
all sides of the FILTER SCREEN assembly are aligned, place the
PIN
end of
FRAME A
on the FILTER
SCREENS, place the
CHANNEL
on the frame adjacent to the
PIN
end over the FILTER SCREENS; then
HINGE
the
frame so the edge of the FILTER SCREENS are inserted in the other
CHANNEL
of FRAME A.
h) Place the
PIN
end of
FRAME B
on the FILTER SCREENS so the
PIN
is seated in the
CHANNEL
of
FRAME A
near
the
FINGER LOOP
, place the
CHANNEL
on the frame adjacent to the
PIN
end over the edge of the FILTER
SCREENS; then
HINGE
the frame so the edge of the FILTER SCREENS are inserted in the other
CHANNEL
of
FRAME B
and the
PIN
on
FRAME B
is seated in the
CHANNEL
of
FRAME A.
i) Adjust
FRAME A
and
B
so other
PINS
are properly seated in the
CHANNEL
of the opposite frame; then
CAREFULLY
connect the
KNURL KNOB
and
STANDPIPE/DOCKING ASSEMBLY
to the
SUCTION FITTING
on the FILTER
SCREEN assembly.
DO NOT OVERTIGHTEN!!!
2.)
“Magnepad” Envelope Filter:
Remove and discard the USED Filter Pad Envelope. CAREFULLY clean the Baffle Assembly and Clip/Stand-pipe assem-
bly in a 3 compartment sink with HOT water and allow these items to air dry. DO NOT USE SOAP!! Reassemble the
Magnepad Envelope Filter using a NEW Magnesol Impregnated Filter Pad Envelope as follows:
a. Insert the
BAFFLE
into the
FILTER PAD ENVEOPE
, when properly inserted the
SUCTION FITTING
will
protude through the hole in the pad.
b. Fold the
FLAP
over (in the direction of the hole) securing the Baffle inside the
FILTER PAD ENVELOPE
.
c.
CAREFULLY
align the
CLIP & STANDPIPE ASSEMBLY
so that the clip can secure the
FLAP
and the
envelope and the
STANDPIPE
will align over the
SUCTION FITTING
protruding through the envelope.
d. Tighten the knurled
NUT
on the
STANDPIPE
to the
SUCTION FITTING
protruding through the envelope.
e. Repeat
DAILY
steps 1 a through 1 d pages 28-30.
Page 30 of 61
Summary of Contents for PAR-3-HE
