ULS VLS Series Service Manual Download Page 44

Page: 44 / 82

VLS Service Manual - REV2015.04

Table of Contents

Component Removal and Replacement

Page | 44

Component Removal and Replacement

8. Check if the system is level by placing a bubble level on the frame of the cart across the two front

casters then the two rear casters. Adjust the level if necessary by turning the adjustment nut.

9. Once the system is level tighten the appropriate locknuts.

Cart Casters

CAUTION:

It is recommended that you obtain the assistance of another person when replacing a caster on this

system.

1. Turn OFF and unplug the VLS.

2. Place each caster in its locked position.

3. Slightly lift the corner of the cart where the caster will be removed.

4. Place a block large enough to provide working clearance slightly behind or in front of the caster being

removed.

5. Using a wrench loosen the locknut and remove the caster by turning the adjustment nut in a counter-

clockwise direction.

6. Installation is opposite of removal.

7. When installing a new caster ensure the locknut is screwed all the way down on the caster.

Summary of Contents for VLS Series



















































































Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands

ULS VLS Series, Service Manual

Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands