ULS VLS Series Service Manual Download | Manualshive

Page: 54 / 82

background image

VLS Service Manual - REV2015.04

Table of Contents

X-Axis

Page | 54

X-Axis

7. Remove the left end support by removing the four screws located on the top (2) and the bottom (2) of

the support.

8. Installation is opposite of removal.

NOTE: During reinstallation It is often easier to feed the belt through the X-Axis rail prior to installing the end
assemblies. Ensure that you do not have a twist in the belt. Failure to remove a twist will result in the laser
system not functioning correctly.

9. Once the

has been reinstalled tension the X-axis belt as in

X-Axis Belt Replacement

.

10. To finish the installation make sure perform the

X-Axis Arm Alignment Check and Adjust (Squaring)

.

«
...
52
53
54
55
56
...
»

Summary of Contents for VLS Series



















































































Reviews:

No comments

Related manuals for VLS Series

Brand: Xerox Pages: 68

Brand: Xerox Pages: 210

Brand: DataCard Pages: 2

Brand: Unimark Pages: 38

WORKCENTRE 5050

Brand: Xerox Pages: 186

7500DX - Phaser Color LED Printer

Brand: Xerox Pages: 5

Brand: Xerox Pages: 2

Brand: Xerox Pages: 16

Brand: Canon Pages: 4

Brand: Xerox Pages: 200

PR-INT-MX-RAVAS-ABLE

Brand: Ravas Pages: 26

Brand: TP-Link Pages: 16

Brand: Felix Storch Pages: 46

Brand: Go Pages: 3

Brand: A&D Pages: 102

Brand: Epson Pages: 16

Brand: Epson Pages: 2

Brand: Epson Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands