ULS VLS Series Service Manual Download

Page: 77 / 82

VLS Service Manual - REV2015.04

Table of Contents

Accessories

Page | 77

Accessories

Beam Window Diffuser

1. Ensure the air source is turned OFF and disconnected from the system.

2. Power OFF and unplug the VLS system.

3. Open the Top Door.

4. Slide the X-axis arm toward the front of the system.

5. Locate and remove the Beam Window Protector by turning it slightly counter-clockwise, lifting up at the

same time.

6. Remove the two screws securing the Fitting Block to the Beam Widow Protector.

7. Unscrew the diffuser from the Fitting Block.

8. Installation is opposite of removal.

Air Assist Diffusers

#2 Mirror Diffuser

1. Ensure the air source (compressor) is turned OFF and disconnected from the system.

2. Power OFF and unplug the VLS system.

3. Open the Top Door.

4. Slide the X-axis arm toward the front of the system.

5. Remove the #2 mirror cover (1) by removing the thumbscrew (2), sliding the cover to the right and then

off the rail.

6. Locate and unscrew the diffuser from the Y Transfer Manifold.

7. Installation is opposite of removal.

Summary of Contents for VLS Series



















































































Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands

ULS VLS Series, Service Manual

Search results

Summary of Contents for VLS Series

Reviews:

Related manuals for VLS Series

Brands by name

Popular brands