1. Turn Mode Selector (B) to MULTIPLAY 1 position.
phone to
socket (connecting a Stereo
makes
microphone System for
1 active), and press
MICRO Switch
holding the Record Button ® down,
turn the Tape Transport Switch ®
STOP to PAUSE position.
During tape movement the MONITOR Switch ® should be in TAPE
Position, and it should be in SOURCE position when tape is not in
motion.
2. Using UHER Adapter Lead K 633, so connect a
UHER W 674 or W 774) to each of the sockets
l and
II or to
the
socket that the
loudspeakers are switched off (see
secs. 2.2, 2.7 and 2.8), first plugging the red
of the headphone
into the yellow plug. The headphone connected to the O II socket or to
the K 633 adapter (yellow connector) is for
by the
cording
the headphone connected to the
socket
K 633 adapter (red connector) is for monitoring by the
To
avoid the possibility of having the headphones destroyed during
back at high volume levels, only headphones with an impedance of
200
or more should be connected to the
l and
sockets.
3. Turn MULTIPLAY/ECHO Control © all the way to the
4. After selecting the tape speed (19 cm/s and 9.5 cm/s are best
suited to sound-with-sound recording), set the record
by
means of the upper knob @ of the MICRO/RADIO Control, making
certain that the MONITOR Switch is in SOURCE position. Next
switch to TAPE monitoring; then begin tape movement by turning
the Tape Transport Switch from PAUSE to START. Recording will
commence on track 1.
5. When recording on track 1 is completed, rewind the tape to the
beginning of the recording Programme. Then switch the Mode
Selector ® to MULTIPLAY 2. The artist should put on his head-
phones. Next, press the Record Button @ and then Start tape
for the second recording. The artist will
the first
recording through his headphones (the volume
be regulated
with the upper knob ® of the VOLUME Control) and can thus
38
the second recording in synchronism. The recording engineer
will hear both recordings if the machine is in TAPE monitoring posi-
tion, and he may regulate the record level of the new recording
with Level Control @ and that of the recorded track being trans-
ferred by means of the MULTIPLAY/ECHO Control
Hence the
relative volume of both recordings may be adjusted whenever
desired.
6. To add still another recording: rewind the tape, switch the Mode
Selector® to MULTIPLAY 1 and repeat the record Operation
already described. If yet another recording is to be added, turn
the Mode Selector © to MULTIPLAY 2, rewind the tape and con-
tinue the alteration
the multiple sound-with-sound recording
desired is completed.
7. For subsequent playback of a sound-with-sound recording, set the
Mode Selector © in MONO 1 position if the switch was in MULTI-
PLAY 1 position when the recording was completed. If at the end
of the recording the Mode Selector was in MULTIPLAY 2 position,
switch it to MONO 2. From this point, playback Operation is the
same
for normal recordings.
Fig.
11
If sound-with-sound recording in Stereo is desired, a second tape re-
corder and a mixing console
UHER MIX 500 A
will be needed.
The recording procedure is described in the operating instructions of
the
Summary of Contents for sg 561 royal
Page 1: ...UHER SG561 ROYAL Betriebsanleitung Operating Instructions Instructions d emploi ...
Page 70: ...K 853 A 124 l T r A261 A 403 G J I L 1 1 3 Akustomat F411 F211 F411 W 214 ...
Page 72: ......
Page 74: ...0 91 10 So Mo Do 8 UHER WERKE MÜNCHEN 366 47019 DEF II 015 1078 R Printed in German ...
