u-blox M9 Integration Manual Download Page 76 | Manualshive

Page: 76 / 95

background image

NEO-M9N - Integration manual

To prevent overstress damage at the RF_IN of your receiver, never exceed the maximum
input power as speciﬁed in the applicable data sheet [

When integrating GNSS receivers into wireless systems, pay special attention to electromagnetic
and voltage susceptibility issues. Wireless systems include components which can produce
Electrostatic Discharge (ESD), Electrical Overstress (EOS) and Electro-Magnetic Interference (EMI).
CMOS devices are more sensitive to such inﬂuences because their failure mechanism is deﬁned by
the applied voltage, whereas bipolar semiconductors are more susceptible to thermal overstress.
The following design guidelines help in designing robust yet cost-eﬀective solutions.

4.6.1 ESD protection measures

GNSS receivers are sensitive to Electrostatic Discharge (ESD). Special precautions are
required when handling. Most defects caused by ESD can be prevented by following strict
ESD protection rules for production and handling. When implementing passive antenna
patches or external antenna connection points, then additional ESD measures as shown in
the ﬁgure below can also avoid failures in the ﬁeld.

Figure 35: RF ESD precautions

4.6.2 EOS precautions

Electrical overstress (EOS) usually describes situations when the maximum input power exceeds
the maximum speciﬁed ratings. EOS failure can happen if RF emitters are close to a GNSS receiver
or its antenna. EOS causes damage to the chip structures. If the RF_IN is damaged by EOS, it is hard
to determine whether the chip structures have been damaged by ESD or EOS.

EOS protection measures as shown in the ﬁgure below are recommended for any designs combining
wireless communication transceivers (e.g. GSM, GPRS) and GNSS in the same design or in close
proximity.

UBX-19014286 - R07

4 Design

Page 76 of 95

C1-Public

«
...
74
75
76
77
78
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: B&K Pages: 88

Brand: B&K Pages: 2

Brand: Quark-Elec Pages: 2

Brand: Chiayo Pages: 8

Brand: FTE Pages: 24

Brand: M/A-Com Pages: 62

Brand: Denver Pages: 14

Brand: Garmin Pages: 41

Brand: Farenheit Pages: 12

Mercury II Digital FTA

Brand: Fortec Star Pages: 3

Brand: Fiio Pages: 8

Brand: FrontRow Pages: 32

Brand: Perstel Pages: 17

Brand: Boss Audio Systems Pages: 23

Pro Comm PCX-U1002

Brand: Peavey Pages: 36

Brand: Blaupunkt Pages: 21

Brand: PowerBass Pages: 12

Brand: August Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands