u-blox M9 Integration Manual Download Page 31 | Manualshive

Page: 31 / 95

background image

NEO-M9N - Integration manual

Part

Recommended part

Description

U1

Seiko Instruments Inc. S-1206B33-I6T2G

LDO which provides 3.3 V to the V_USB pin.

C1, C2

Depends on USB LDO (U1) speciﬁcation

U1 LDO decoupling capacitor.

D1

ST Microelectronics USBLC6-2

Low capacitance ESD protection diodes to avoid cross
supply.

R1

100 kΩ

Pull-down resistor in case USB interface is not used.
Not needed it if USB is used.

R2, R3

27 Ω 5% 0.1W

Serial termination resistor for USB.

Table 15: Recommended components for USB interface

3.8 Predeﬁned PIOs

In addition to the communication ports, there are some predeﬁned PIOs provided by NEO-M9N to
interact with the receiver. These PIOs are described in this chapter.

If hardware backup mode is used a proper isolation of the interfaces is needed.

3.8.1 D_SEL

The D_SEL pin can be used to conﬁgure the functionality of the combined UART1, I2C, and SPI pins.
It is possible to conﬁgure the pins as UART1 + I2C, or as SPI. SPI is not available unless D_SEL pin
is set to low. See

below.

Pin no.

D_SEL == 0

D_SEL == 1

20

SPI_MISO

UART1 TXD

21

SPI_MOSI

UART1 RXD

18

SPI_CS_N

I2C SDA

19

SPI_CLK

I2C SCL

Table 16: D_SEL conﬁguration

3.8.2 RESET_N

The NEO-M9N provides the ability to reset the receiver. The RESET_N pin is an input-only pin with
an internal pull-up resistor. Driving RESET_N low for at least 100 ms will trigger a cold start.

The RESET_N pin will delete all information and trigger a cold start. It should only be used
as a recovery option.

3.8.3 SAFEBOOT_N

The NEO-M9N provides a SAFEBOOT_N pin that is used to command the receiver safe boot mode.

If this pin is low at power up, the receiver starts in safe boot mode and GNSS operation is disabled.

The safe boot mode can be used to recover from situations where the ﬂash content has become
corrupted and needs to be restored.

In safe boot mode the receiver runs from a passive oscillator circuit with less accurate timing and
hence the receiver is unable to communicate via USB.

In this mode only UART1, I2C or SPI communication is possible. For communication via UART1 in
safe boot mode, the host must send a training sequence (0x55 0x55 at 9600 baud) to the receiver in
order to begin communication. After this the host must wait at least 2 ms before sending any data.

UBX-19014286 - R07

3 Receiver functionality

Page 31 of 95

C1-Public

«
...
29
30
31
32
33
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: Garod Radio Pages: 29

Brand: Samsung Pages: 10

Brand: Icom Pages: 26

Brand: Radionics Pages: 73

Brand: Yamaha Pages: 128

Brand: Yamaha Pages: 147

Brand: Fisher Pages: 14

Brand: Teac Pages: 4

Brand: Boss Audio Systems Pages: 14

Brand: KBSOUND Pages: 16

Brand: RCAVICTOR Pages: 26

Brand: Sigma Pages: 23

echomap 40 series

Brand: Garmin Pages: 22

Brand: Icom Pages: 48

Brand: NAD Pages: 48

Brand: Albrecht Pages: 76

Brand: Aiwa Pages: 16

Lanzar Vibe VBD2600MP

Brand: Lanzar Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands