u-blox M9 Integration Manual Download Page 71 | Manualshive

Page: 71 / 95

background image

NEO-M9N - Integration manual

Avoid high resistance on the

V_BCKP

line: During the switch from main supply to backup

supply, a short current adjustment peak can cause a high voltage drop on the pin with
possible malfunctions.

If no backup supply voltage is available, connect the

V_BCKP

pin to

VCC

.

Allow all I/O including UART and other interfaces to ﬂoat or connect to a high impedance in
HW backup mode (V_BCKP supplied when VCC is removed). See the

is essential that the interfaces and PIOs are isolated with open-drain buﬀers when VCC is
removed to prevent the chip from being powered through these circuits.

In software backup mode the receiver remains supplied and backup is handled with software
commands. See the NEO-M9N Interface description [

] for more information.

4.2.3 V_USB: USB interface power supply

V_USB supplies the USB interface. If the USB interface is not used, the V_USB pin must be connected
to GND. For more information about correctly handling the V_USB pin, see

section.

4.3 NEO-M9N minimal design

The minimal electrical circuit for NEO-M9N operation using the UART1 interface is shown in

below.

Figure 31: Minimal NEO-M9N design

For a minimal design with the NEO-M9N GNSS modules, the following functions and pins should be
considered:

• Connect the power supply to VCC and V_BCKP.
• If hot or warm start operations are needed, connect a backup battery to V_BCKP.
• If USB is not used connect V_USB to ground.
• Ensure an optimal ground connection to all ground pins of the NEO-M9N GNSS module.

UBX-19014286 - R07

4 Design

Page 71 of 95

C1-Public

«
...
69
70
71
72
73
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: B&K Pages: 88

Brand: B&K Pages: 2

Brand: Daikin Pages: 4

Brand: Harman Kardon Pages: 11

Brand: Harman Kardon Pages: 8

Brand: Harman Kardon Pages: 9

Brand: Harman Kardon Pages: 3

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 18

Brand: Harman Kardon Pages: 32

Brand: Harman Kardon Pages: 50

Brand: Quark-Elec Pages: 2

Brand: Streetwize Pages: 2

Brand: Audiotech Pages: 7

Brand: Shure Pages: 4

Brand: Icom Pages: 48

Brand: Aiwa Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands