u-blox M9 Integration Manual Download Page 60 | Manualshive

Page: 60 / 95

background image

NEO-M9N - Integration manual

Figure 23: Time pulse signal with the example parameters

3.13.2 Timemark

The receiver can be used to provide an accurate measurement of the time at which a pulse was
detected on the external interrupt pin. The reference time can be chosen by setting the time source
parameter to UTC, GPS, GLONASS, BeiDou, Galileo or local time in the CFG-TP-* conﬁguration group.
The UTC standard can be set in the CFG-NAVSPG-* conﬁguration group. The delay ﬁgures deﬁned
with CFG-TP-* are also applied to the results output in the UBX-TIM-TM2 message.

A UBX-TIM-TM2 message is output at the next epoch if

• The UBX-TIM-TM2 message is enabled, and
• A rising or falling edge was triggered since last epoch on one of the EXTINT channels.

The UBX-TIM-TM2 messages includes the time of the last timemark, new rising/falling edge
indicator, time source, validity, number of marks and an accuracy estimate.

Only the last rising and falling edge detected between two epochs is reported since the
output rate of the UBX-TIM-TM2 message corresponds to the measurement rate conﬁgured
with CFG-RATE-MEAS (see

below).

UBX-19014286 - R07

3 Receiver functionality

Page 60 of 95

C1-Public

«
...
58
59
60
61
62
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: National Pages: 14

Brand: Icom Pages: 7

Brand: Icom Pages: 13

Brand: Icom Pages: 43

Brand: Icom Pages: 7

Brand: Icom Pages: 13

Brand: Icom Pages: 72

Brand: Icom Pages: 96

Brand: Icom Pages: 64

Brand: Icom Pages: 57

Brand: Icom Pages: 64

Brand: Icom Pages: 28

Brand: Icom Pages: 80

Brand: Icom Pages: 108

Brand: Icom Pages: 139

Brand: Icom Pages: 36

Brand: Icom Pages: 44

Brand: Icom Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands