u-blox M9 Integration Manual Download Page 45

Page: 45 / 95

NEO-M9N - Integration manual

• The receiver will be forced to stay awake if

EXTINTWAKE

is enabled and the conﬁgured EXTINT

pin is set to "high" and it will be forced to stay in

(Inactive) awaiting next search/Fix

states if

EXTINTBACKUP

is enabled and the conﬁgured EXTINT pin is set to "low" (see

EXTINT pin control

for details).

• The receiver will be forced to stay awake if

EXTINTINACTIVE

is enabled and the conﬁgured

EXTINT is toggling and it will be forced to stay in

(Inactive) awaiting next search/Fix

states if

conﬁgured EXTINT state is not changed for longer time than

EXTINTINACTIVITY

(see

EXTINT pin

control

for details).

3.11.2.1.2 On/oﬀ operation - long update period

The diagram below illustrates how on/oﬀ operation works:

Figure 19: Diagram of on/oﬀ operation

• When the receiver is switched on, it ﬁrst enters

Acquisition

state.

• If it is able to obtain a valid position ﬁx within the time given by the

Acquisition Timeout

, it

switches to

Tracking

state. Otherwise it enters

(Inactive) awaiting next search

state and re-

starts after the conﬁgured search period (minus a start-up margin).

• As soon as the receiver gets a valid position ﬁx (one passing the navigation output ﬁlters), it

enters

Tracking

state. Upon entering

Tracking

state, the

ONTIME

starts.

• Once the

ONTIME

is over,

(Inactive) awaiting next fix

state is entered and the receiver re-starts

according to the conﬁgured update grid (see section

Grid oﬀset

for an explanation).

• If the signal is lost while in

Tracking

state,

Acquisition

state is entered. If the signal is not

found within the acquisition timeout, the receiver enters

(Inactive) awaiting next search

state.

Otherwise the receiver will re-enter

Tracking

state and stay there until the newly started

ONTIME is over.

3.11.2.1.3 Cyclic tracking operation - short update period

The diagram below illustrates how cyclic tracking operation works:

Figure 20: Diagram of cyclic tracking operation

• When the receiver is switched on, it ﬁrst enters

Acquisition

state.

• If it is able to obtain a position ﬁx within the time given by the acquisition timeout, it switches

Tracking

state. Otherwise, it will enter

(Inactive) awaiting next search

state and re-start

within the conﬁgured search grid.

UBX-19014286 - R07

3 Receiver functionality

Page 45 of 95

C1-Public

Summary of Contents for M9
































































































Search results

Summary of Contents for M9

Reviews:

Related manuals for M9

Brands by name

Popular brands

u-blox M9, Integration Manual

Search results

Summary of Contents for M9

Reviews:

Related manuals for M9

Brands by name

Popular brands