u-blox M9 Integration Manual Download Page 79 | Manualshive

Page: 79 / 95

background image

NEO-M9N - Integration manual

4.8 Layout

This section details layout and placement requirements of the NEO-M9N module.

4.8.1 Placement

GNSS signals at the surface of the Earth are below the thermal noise ﬂoor. A very important factor in
achieving maximum GNSS performance is the placement of the receiver on the PCB. The placement
used may aﬀect RF signal loss from antenna to receiver input and enable interference into the
sensitive parts of the receiver chain, including the antenna itself. When deﬁning a GNSS receiver
layout, the placement of the antenna with respect to the receiver, as well as grounding, shielding and
interference from other digital devices are crucial issues and need to be considered very carefully.

Signal loss on the RF connection from antenna to receiver input must be minimized as much as
possible. Hence, the connection to the antenna must be kept as short as possible.

Ensure that RF critical circuits are clearly separated from any other digital circuits on the system
board. To achieve this, position the receiver digital part closer to the digital section of the system
PCB and have the RF section and antenna placed as far as possible away from the other digital
circuits on the board.

A proper GND concept shall be followed: The RF section shall not be subject to noisy digital supply
currents running through its GND plane.

4.8.2 Thermal management

During design-in do not place the receiver near sources of heating or cooling. The receiver oscillator
is sensitive to sudden changes in ambient temperature which can adversely impact satellite signal
tracking. Sources can include co-located power devices, cooling fans or thermal conduction via the
PCB. Take into account the following questions when designing in the receiver.

• Is the receiver placed away from heat sources?
• Is the receiver placed away from air-cooling sources?
• Is the receiver shielded by a cover/case to prevent the eﬀects of air currents and rapid

environmental temperature changes?

High temperature drift and air vents can aﬀect the GNSS performance. For best
performance, avoid high temperature drift and air vents near the receiver.

4.8.3 Package footprint, copper and paste mask

Copper and solder mask dimensioning recommendations for the NEO-M9N module packages are
provided in this section.

These are recommendations only and not speciﬁcations. The exact copper, solder and paste
mask geometries, distances, stencil thickness and solder paste volumes must be adapted
to the speciﬁc production processes (e.g. soldering etc.) of the customer.

UBX-19014286 - R07

4 Design

Page 79 of 95

C1-Public

«
...
77
78
79
80
81
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: Sagem Pages: 3

Brand: Xtrend Pages: 65

Brand: Blaupunkt Pages: 28

Brand: Harman Kardon Pages: 13

Brand: Zamel Pages: 4

Brand: Blaupunkt Pages: 8

Brand: TOP VEHICLE TECH Pages: 8

Brand: Immersion Pages: 5

VM9412 - In-dash DVD Receiver

Brand: Jensen Pages: 38

Campersat Autoseek Autoskew System 4441

Brand: Campersat Pages: 14

Brand: Skoda Pages: 13

Brand: TV Star Pages: 10

Brand: Dual Pages: 33

Brand: Grundig Pages: 38

Brand: Lotek Wireless Pages: 36

Brand: GbSat Pages: 52

Brand: SAL Pages: 32

Brand: Cabletron Systems Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands