manualshive.com logo in svg

u-blox M9, Integration Manual

The user-friendly Ask Proxima M9 comes with a comprehensive User Manual, providing detailed instructions for hassle-free setup and use. You can easily download the manual for free from manualshive.com, ensuring that you have all the necessary information at your fingertips to make the most of your product.

Share
Download
background image

NEO-M9N - Integration manual

• If USB is not used, connect the V_USB pin to ground.
• For USB devices: Is the V_USB voltage within the specified range?
• It is recommended to have a separate LDO for V_USB that is enabled by the module VCC. This is

to comply with the USB self-powered specification.

• If USB is used, is there a 1 uF capacitor right near the V_USB pin? This is just for the V_USB pin.
• Is there a 1 uF cap right next to the module VCC pin?
• Compare the peak current consumption of the NEO-M9N GNSS module with the specification

of your power supply.

• GNSS receivers require a stable power supply. Avoid series resistance (less than 0.2 Ω) in

your power supply line (the line to VCC) to minimize the voltage ripple on VCC. See the NEO-
M9N 

Power supply

 section in the 

Design

 chapter for more information on the power supply

requirements.

• Allow all I/O to Float/High impedance (High-Z) when VCC is not applied.

4.9.2 Backup battery

Check backup supply requirements and schematic:

• For achieving a minimal time to first fix (TTFF) after a power down (warm starts, hot starts),

make sure to connect a backup battery to V_BCKP.

• Verify that your battery backup supply can provide the battery backup current specified in the

applicable data sheet.

• Allow all I/O including UART and other interfaces to Float/High impedance in HW backup mode

(battery backup connected with VCC removed).

4.9.3 RF front-end circuit options

The first stages of the signal processing chain are crucial to the overall receiver performance.

When  an  RF  input  connector  is  employed  this  can  provide  a  conduction  path  for  harmful  or
destructive electrical signals. If this is a likely factor the RF input should be protected accordingly.

Additional points on the RF input

• What is the expected quality of the signal source (antenna)?
• What is the external active antenna signal power?
• What is the bandwidth and filtering of the external active antenna?
• Does the external antenna and any optional filtering components meet the group delay

variation requirements?

Are  destructive  RF  power  levels  expected  to  reach  the  RF  input?  Is  interference  from  wireless
transmitters expected?

• What are the characteristics of these signals (duty cycle, frequency range, power range,

spectral purity)?

• What is the expected GNSS performance under interference conditions?

Is there a risk of RF input exposure to excessive ESD stress?

• In the field: Can the user access the antenna connector?
• PCB / system assembly: Is there risk that statically charged parts (e.g. patch antennas) may be

discharged through the RF input?

The following subsections provide several options addressing the various questions above:

In some applications, such as cellular transceivers, interference signals may exceed the
maximum power rating of the RF_IN input. To avoid device destruction use of external input
protection is mandatory.

UBX-19014286 - R07

 

4 Design

Page 83 of 95

C1-Public

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Ramsey Electronics FR220 Instruction Manual preview
FR220
Brand: Ramsey Electronics Pages: 28
Magenta MultiView II DVI-Rx-1K Installation And User Manual preview
MultiView II DVI-Rx-1K
Brand: Magenta Pages: 33
Magenta MultiView II AK600 Quick Reference & Setup Manual preview
MultiView II AK600
Brand: Magenta Pages: 28
VDO MS 4100 - Datasheet preview
MS 4100 -
Brand: VDO Pages: 2
VDO CD 4203 - Datasheet preview
CD 4203 -
Brand: VDO Pages: 2
Xoro HRT 7622 User Manual preview
HRT 7622
Brand: Xoro Pages: 44
Xomax XM-CDB624 Installation Manual preview
XM-CDB624
Brand: Xomax Pages: 18
VDO TR 7322U-OR - Datasheet preview
TR 7322U-OR -
Brand: VDO Pages: 1
Yaesu FTM-100DE Instruction Manual preview
FTM-100DE
Brand: Yaesu Pages: 15
Yaesu FT-891 Technical Supplement preview
FT-891
Brand: Yaesu Pages: 99
Yaesu FT-891 Reference Book preview
FT-891
Brand: Yaesu Pages: 20
Yaesu FTM-100DR Quick Manual preview
FTM-100DR
Brand: Yaesu Pages: 2
Yaesu FTM-100DR Operating Manual preview
FTM-100DR
Brand: Yaesu Pages: 176
ADI AR-147 User Manual preview
AR-147
Brand: ADI Pages: 47
Tesla TE-380 Mini User Manual preview
TE-380 Mini
Brand: Tesla Pages: 68
Xantech Dinky Link 480B-30 Install Manual preview
Dinky Link 480B-30
Brand: Xantech Pages: 3
Sirius Satellite Radio Streamer GT SIR-SL1 User Manual preview
Streamer GT SIR-SL1
Brand: Sirius Satellite Radio Pages: 25
PowerBox Systems PBR-5S Instruction Manual preview
PBR-5S
Brand: PowerBox Systems Pages: 3

Brands by name

Popular brands

Load more brands