u-blox M9 Integration Manual Download Page 2 | Manualshive

Page: 2 / 95

background image

NEO-M9N - Integration manual

Document information

Title

NEO-M9N

Subtitle

Standard precision GNSS module

Document type

Integration manual

Document number

UBX-19014286

Revision and date

R07

13-Dec-2021

Disclosure restriction

C1-Public

This document applies to the following products:

Type number

Firmware version

IN/PCN reference

RN reference

NEO-M9N-00B-00

SPG 4.04

UBX-21029274

UBX-20036165

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this
document. Copying, reproduction, modiﬁcation or disclosure to third parties of this document or any part thereof is only
permitted with the express written permission of u-blox.
The information contained herein is provided "as is" and u-blox assumes no liability for its use. No warranty, either express
or implied, is given, including but not limited to, with respect to the accuracy, correctness, reliability and ﬁtness for a
particular purpose of the information. This document may be revised by u-blox at any time without notice. For the most recent
documents, visit www.u-blox.com.
Copyright © 2021, u-blox AG.

UBX-19014286 - R07

Page 2 of 95

C1-Public

«
1
2
3
4
...
»

Summary of Contents for M9
































































































Reviews:

No comments

Related manuals for M9

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 39

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 42

Brand: Ramsey Electronics Pages: 28

Brand: Ranger Communications Pages: 11

Brand: Yamaha Pages: 8

Brand: Yaesu Pages: 5

Brand: Phonak Pages: 4

Brand: Teac Pages: 44

Brand: Icom Pages: 40

Brand: Magtisat Pages: 28

Brand: Audi Pages: 35

Brand: AMG Pages: 8

Brand: Sennheiser Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands