background image

ACM 400 S motor control unit 

 

 

19 / 24 

10) 

Disposal 

The control unit does not contain any materials for which known disposal regulations 
exist  at  the  time  these  instructions  were  written  (November  2005).  The  control  unit 
does not contain any built-in energy sources. 
 

11) 

Extensions/Add-Ons 

[X3] 
On  the  printed  circuit  board  there  are  three  slots  for  optional  extensions/add-ons, 
which have already been partly covered in these instructions: 
 
[X3.1]  For  the  "Open",  "Closed",  "Pulse"  and  "Partial  opening"  functions  or  the 
universal-output, a 

radio receiver 

can be installed in the 

"Radio"

 slot (see page 13) 

[X4].  This  is  described  in  greater  detail  in  the  installation  instructions  for  the  radio 
receiver. 
[X3.2]  At 

"Slot  A"

  the  optional  available  multi-functional  card  MMZ442-50  can  be 

inserted with the following functions: 

 

 

 

 

 

 

 

 

The 

MMZ442-50

  card  works  correctly  from  software  version  V1.2  for  the  motor 

control unit. 
 
[X3.3]  An  optional  membrane  keyboard  can  be  connected  to  the  control  unit  (see 
pages 

Fehler! Textmarke nicht definiert.

, 14, 17). For space reasons, its use is not 

recommended together with the plug-in card MMZ442-50. 
 

Summary of Contents for ACM 400 S

























Reviews: