5
1
,
5 mm.
Adjust the knob (
3
) to set the distance between depth limiter sleeve tip
(
2
) and screw head to about 1 mm, as shown in Fig.
D 1
or
D 2
.
Drive a trial screw into the material or a replacement item. If the depth is
not suitable for the screw, re-adjust it to obtain a proper setting.
Proper screw driving depth adjustment is crucial. Some examples for
driving screws into plasterboards are presented in the table below:
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
IN USE:
n
Turning on/off
:
Connect the power cord plug to the mains socket.
ź
To switch the power
on
press the switch (
7
) and hold it in this position.
ź
To immobilize the switch in pressed position, press the lock (
8
).
n
Replacing tool bits
(Fig.
B
)
:
ź
To switch the power
off
, release the switch (
7
), or when immobilized
with the lock button (
8
), press for a moment and then release it
immediately.
To remove a tool bit (
1
) from the chuck, first remove the driving depth
limiter (
4
) by sliding it forwards. Then, catch the bit with pliers and pull it
out from the magnetic chuck (
11
). Swinging the pliers when pulling the
bit out sometimes makes it easier to remove it. You can also remove and
replace the multi-purpose chuck (
11
), if necessary.
TIPS REGARDING OPERATION:
n
Setting the rotation direction
(Fig.
A1
)
NOTE:
The power tool should be placed on a screw when it is off.
The rotation direction selector (
6
) can be used to change the power tool
When driving larger and longer screws into a hard material, it is
spindle direction. However, it is not possible when the switch (
7
) is
recommended to make a pilot hole first, a bit deeper and with a lower
pressed.
diameter than the actual screw outer diameter.
Right rotation direction:
To drive screw press the rotation direction
When the screw is to be driven within the vicinity of the material edge the
selector (
6
) to the left (when looking from the back of the driver) until
pilot borehole prevents from undesired chipping of the material.
resistance is felt (position
R
).
If the screw is driven with abnormal difficulty the screw must be
Left rotation direction:
To release or undo screws or nuts press the
retracted and the pilot borehole diameter should be enlarged.
rotation direction selector (
6
) to the right (when looking from the back of
Anyway, when problem to drive the screw in persists (e.g. in case of hard
the driver) until resistance is felt (position
L
).
wood grades) try to use a lubricating agent (e.g. liquid soap). Press the
n
Setting drilling depth
(see Fig.
C
)
tool to the screw with sufficient force to avoid spontaneous rotation of
the driving bit in the screw head. Use only those bits that accurately
Using the depth limiter knob (
3
) it is possible to set how deep the screw
match the bit head. When the screw head is damaged further driving the
head sinks in the material.
screw in or out may prove infeasible.
Turning the knob (
3
) clockwise (when looking from the back of the
ź
Place the screw onto the driving bit (
1
). Screws are held in place
driver) increases the driving depth, while turning it counterclockwise
(when looking from the back of the driver) decreases the driving depth.
automatically by the chuck magnetic force (
11
). Press the screw tip
One full turn of the depth setting knob changes the drilling depth by
against the material until driving depth limiter (
4
) touches its surface.
BEFORE YOU START:
1. Make sure that the power supply parameters match the data plate
parameters.
2. Make sure that the driver switch (
7
) is in off position and on/off switch
lock (
8
) is released. Do not put the operating driver aside when the
switch lock is on. To switch the lock off, press the button (
7
) again.
3
. When using an extension cable make sure its parameters and wire
cross sections match the driver parameters. Use the shortest
extension cords possible. The extension cord used should be
completely unfolded.
NOTE:
Prior to any servicing or preparing the power tool for operation
always make sure it is disconnected from the power supply.
n
Controlling the speed
By increasing or decreasing the pressure on switch (
7
) the user can
control the rotational speed steplessly.
Low pressure on the switch
results in low speed. Increasing the pressure raises the speed.
NOTE:
Use the rotation direction selector (
6
) when the power tool is off.
Equipment class
II
Weight
1,5
к
g
Sound pressure level (LpA)
dB(A)
6
Sound power level (LwA)
dB(A)
97
Vibration level according to
EN 60745-1
(measuring
2
tolerance
-
1
,
5
m/s
)
driving with no impact a
h
2
2,32 m/s
6 mm (¼")
Max screw/bolt diameter
Too deep.
Screw head makes a hole in the plasterboard surface
and enables damp to penetrate under the cover.
Too shallow.
Screw head projects over the plasterboard instead of
being hidden inside it.
Correct.
Screw head is located below the surface, at the same
time it does not puncture the plasterboard.
M
easuring tolerance
LpA
,
LwA
3
dB(A)
Summary of Contents for TMGK500
